IBM Infoprint 4247-Z03 Parts
Please call for parts assistance
Looking for whole machines? Click here
1 177 301 75P0516 Damper D.2D (Misc. Kit item 1) 302 75P0516 Nut Hex M4 (Misc. Kit item 11) 304 41U2329 Washer Lock 305 306 NP Metal Base Assembly 307 NP Vibrodamper 320 75P0516 Screw M4x6 (Misc. Kit item 5) 376 08H7355 Screw M3x8 (Misc. Kit item 7) 392 NP Vibrodamp V | |
2 Front cover assembly 353 303 75P0516 8 Screw, M3x6 (Misc. Kit item 2) 304 41U2329 Washer, Flat, D4.3 (Misc. Kit item 13) 320 75P0516 Screw, M4x6 (Misc. Kit item 5) 321 75P0519 Friction Lever Left 322 354 NP Foam, sound, front 356 NP Handle, chrome 357 NP Pivot assembly, front 358 NP Bracket, shaft 359 5P0518 Pin, shaft (Also in Misc. Kit item 9) 360 75P0518 Clip, shaft (Also in Misc. Kit item 18) 361 372 NP Logo 374 NP Spacer 381 NP Shield 384 NP Magnet assembly 385 NP Gasket 390 41U2329 Washer Flat D4.3 (Misc. Kit item 13) 393 41U2328 Screw 2.2x9.5 (Misc. Kit item 4) | |
3- Left- and right- side cover assemblies 308 309 Foam, sound 310 Left Handle 312 75P0516 Screw, 2.9x9.5 (Misc. Kit item 3) 313 75P0516 Bracket (Misc. Kit item 13) 314 NP Magnet 315 75P0516 Retainer, ring, D10 (Misc. Kit item 4) 317 NP Gasket, left cover 316 309 NP Foam, sound 311 NP Pocket, right lateral 318 NP Gasket, right cover 319 75P0516 Stud 18 (Misc. Kit item 14) | |
4- Rear cover assembly and controller board 366 320 75P0516 Screw, M4x6 (Misc. Kit item 5) 367 NP Foam, sound 362 NP Cover, engine and power 363 NP Baffle 365 75P0516 Screw, 3.9x13 (Misc. Kit item 10) 368 368 368 373 NP Label 375 NP Separator, paper 380 NP Slot Plug 380A NP Cap Stud (installed on controller) 386 NP Label Notes: 1. SBCS = Single Byte Character Set controller. 2. Controller firmware included. There is no need to flash download firmware into the new controller under normal conditions. 3. Controller Board part numbers are exclusive to the Model Z03 Printer. | |
Assembly 5: Cover assembly, top 333 303 75P0516 Screw M3x4 (Misc. Kit item 6) 314 NP Magnet 315 75P0516 Retainer, ring, D10 (Misc. Kit item 4) 320 75P0516 Screw, M4x6 (Misc. Kit item 5) 343 NP Gasket, left 344 NP Gasket, right 345 NP Gasket, front 338 NP Lower Foam 337 NP Conveyor, paper 339 NP Hinge flap, left 340 NP Hinge flap, right 334 336 NP Foam 341 346 347 75P0516 Screw, M6x30 (Misc. Kit item 15) 348 NP Washer D.6.5 350 75P0516 20 Washer, spring (Misc. Kit item 16) 351 75P0516 Nut M6 (Misc. Kit item 8) 352 75P0516 Nut Selflock M6 (Misc. Kit item 17) 370 NP Screw, M4x25 371 NP Friction Spacer 377 NP Pivot Block 397 NP Cover Stop 398 NP Spacer | |
Assembly 6: Board (front), encoder 1 3 Spacer, sensor 4 5 08H7355 Screw, M3x8 6 08H7355 Screw, M3x8 8 | |
Assembly 7: Boards and fans (rear) engine, power supply, and fans 14 08H7355 Screw, M3x8 (Misc. Kit item 15) 24 25 36 NP Slot Plug 50 08H7355 Screw, M3x8 (Misc. Kit item 5) 51 41U2328 Screw 2.2x9.5 (Misc. Kit item 4) 53 NP Support 61 41U2328 10 Screw, 2.9x9.5 (Misc. Kit item 11) 62 08H7355 Screw, M4x6 (Misc. Kit item 11) 63 64 65 66 NP Rubber fix fan 71 41U2290 Cable Clamp (Misc. Kit item 12) 78 NP Support 93 NP Cap Stud (Installed on Controller) 108 44D8979 Slot assembly kit (note 2) 110 113 NP Ground Strip 114 08H7355 Screw M3x6 (Misc. Kit item 13) 115 115 115 170 NP Protection Mylar 177 NP Base Assembly 182 182A 184 08H7355 Screw M3x6 (Misc. Kit item 17) 187 41U2329 Washer D 3.2 (Misc. Kit item 25) 189 NP Shield Cable 191 NP Label 192 NP Carriage Motor Support 202 41U2329 Washer 203 NP Ground Strip 204 NP Label Warning 205 NP Support 387 403 44D8979 Grounding Plate (metal insert) together with slot assembly 108 Notes: 1. Item 110 is the Back Panel board of the Slot Assembly and plugs into the Engine board. 2. The Slot Assembly Kit (item 108) includes a grounding plate (item 403). 3. SBCS = Single Byte Character Set controller. 4. Controller firmware included. There is no need to flash download firmware into the new controller under normal conditions. 5. Controller Board part numbers are exclusive to the Model Z03 Printer. 6. The Operator Panel Cable requires the Operator Panel Cable Extension (not shown), P/N 44D9003, to reach between the Engine board and the Operator Panel Connector. | |
Assembly 8: Carriage assembly 1 34 41U2328 Screw, M2.5x4 35 36 Plate, mask 59A Felt, oil 59B Flange | |
Assembly 9: Mechanical assembly I 1 NP Mechanical assembly I 2 NP Right Frame 3 NP Left Frame 4 NP Base Frame 5 NP Guide Assembly 6 NP Lower Feeder Assembly (note 1) 7 8 08H7351 Bush (Misc. Kit item 7) 9 41U2329 Ring Benzing D. (Misc. Kit item 6) 13 41U2328 9 Screw, M3.5x13 (Misc. Kit item 1) 10 NP Front Pulley 14 08H7355 Screw, M3x6 (Misc. Kit item 1) 15 08H7355 Screw M3x4 (Misc. Kit item 3) 18 41U2329 Ring Ret. D.8 (Misc. Kit item 7) 22 08H7353 Spacer (Misc. Kit item 3) 23 41U2328 Screw, M2.2x9.5 (Misc. Kit item 4) 24 41U2290 Sensor Plate (Misc. Kit item 4) 25 08H7355 Screw M2x8 (Misc. Kit item 4) 28 29 30 41U2290 Bearing Retainer (Misc. Kit item 5) 31 08H7351 Bearing (Misc. Kit item 8) 32 08H7355 Screw, M3x8 (Misc. Kit item 5) 41 42 08H7355 Screw, M3x8 (Misc. Kit item 7) 43 44 08H7355 Screw, M3x10 (Misc. Kit item 8) 45 47 48 51 08H7355 Screw, M4x6 (Misc. Kit item 9) 53 NP Cable Profile Assembly 54 64 41U2329 Washer 81 87 08H7355 Screw M3x6 (Misc. Kit item 13) 90 94 41U2329 Ring Benzing D.6 (Misc. Kit item 5) 101 101A 104 41U2329 Ring Benzing D.4 (Misc. Kit item 3) 114 119 41U2290 Vibrodamp (Misc. Kit item 1) 122 41U2290 Cable Clamp (Misc. Kit item 10) 126 41U2290 Damper VGA (Misc. Kit item 2) 129 NP Label 133 41U2329 Washer Flat D3.2 (Misc. Kit item 20) 138 141 41U2328 Screw 2.9x9.5 (Misc. Kit item 11) 149 160 NP Gear, Tractor 168 NP Bracket Pulley Pivot 169 41U2328 Screw 3.5x19 (Misc. Kit item 17) 190 NP Gear Protection (packaged per pack) 198 41U2290 Cable Clamp (Misc. Kit item 13) 01 (note 2) 03 (note 2) 04 (note 2) Notes: 1. Lower Feeder Assembly (item 6) is for cut sheet and is nonfunctional in this regard. The purpose of the bar is to hold tension between the side frames. 2. Opto Interrupters V03 and V04 and Reflective Sensor V01 are included in the Sensors Cable Assembly. Opto Interrupter Sensors can be individually replaced. | |
Assembly 10: Mechanical assembly II 2 NP Right Frame 3 NP Left Frame 17 NP Bracket 35 59 59A 59B 59C 08H7355 Screw M3x8 (Misc Kit item 7) 59D NP Spacer Sensor (note 1) 59E 08H7355 Screw M3x8 (Misc Kit item 15) 59F NP Mask Plate 59G 41U2328 Screw M2.5x4 (note 1) (Misc Kit item 9) 60 61 NP Belt Bracket (in the carriage assembly) 62 41U2328 Screw M2.9x13 (Misc Kit item 7) 63 63H6274 Rear Bar Kit (note 2) 64 41U2329 Washer (Misc Kit item 8) 65 08H7355 Screw M4x8 (Misc Kit item 10) 66 67 41U2290 Shaft Retainer (Misc Kit item 7) 69 08H7351 Carriage Bush (Misc Kit item 13) 70 41U2329 Nut hexagonal M5 (Misc Kit item 18) 71 NP Screw M5x10 72 75P0543 Loose Pulley Bracket 73 75P0544 Pulley Assembly 74 75P0544 Pivot 75 76 NP Carriage Motor Support 77 41U2290 Motor Damp (Misc Kit item 3) 78 41U2290 Stud (Misc Kit item 8) 79 80 08H7355 Screw M4x6 (Misc Kit item 11) 82 83 08H7355 AFTA Stud (Misc Kit item 22) 84 85 41U2329 Ring Benzing D2.3 (Misc Kit item 1) 86 -87 08H7355 Screw M3x6 (Misc Kit item 13) 93 08H7309 Double Gear 94 41U2329 Ring Benzing D.6 (Misc Kit item 5) 97 08H7310 Moveable gear 109 112 08H7355 Screw M3x8 (Misc Kit item 15) 117 75P0543 Support Bracket Assembly 118 NP Strip Plastic/Bracket Support 123 08H7355 Screw M3x4 (Misc Kit item 16) 129 NP Thermal Label 136 08H7353 O-Ring (Misc Kit item 11) 141 41U2328 Screw M2.9x9 (Misc Kit item 6) 144 08H7351 Wear Resistant Spring (Misc Kit item 12) 147 63H6274 Eccentric Bushing (note 2) 148 63H6274 Screw M4x12 (note 2) 184 08H7355 Screw M3x6 (Misc Kit item 1) Notes: 1. Carriage Assembly (item 59) includes items 59A, 59B, 59C, 59D, 59E, 59F, and 59G. Also assembled on the carriage, two bushings, two oiled felts, two flanges, and the Ribbon Mask (item 35). 2. Rear Bar Kit includes items 63, 147, and 148 | |
Assembly 11: Mechanical assembly III 2 NP Right Frame 3 NP Left Frame 49 41U2329 Ring Benzing D.4 (Misc. Kit item 3) 87 08H7355 Screw M3x6 (Misc. Kit item 13) 102 (note 1) 103 (note 1) (Includes Support and Drive Shafts) 104 NP Ring Benzing D.4 (note 1) 105 106 08H7355 Screw, M3x1 (Misc. Kit item 14) 107 41U2328 Screw, M2.9x19 (Misc. Kit item 8) 108 75P0537 Right Cartridge Support (Packaged 5 per pack) 114 128 41U2329 Washer, Quick Lock (Misc. Kit item 15) 129 NP Warning Label 132 145 41U2329 Pivot Mech. (Misc. Kit item 26) 146 NP Washer 60D (note 1) 150 NP Tractor Support Bracket Right 151 NP Tractor Support Bracket Left Notes: 1. Ribbon Drive Assembly item 103 includes items 102, 104, and 146. | |
Assembly 12: Mechanical assembly and base 175 176 177 NP Base Assembly 179 41U2328 Screw 3.9x13 (Misc. Kit item 15) 186 63H6062 Fastener Loop Self-Lock (50 per pack) 188 | |
Assembly 13: Cover Assembly, Operator Panel 13 303 08H7355 Screw M3x6 (Misc. Kit item 17) 321 75P0519 Left Shaft Friction 322 75P0518 Right Shaft Friction 323 44D8956 Metal Operator Panel Support 324 NP Interlock Support 325 NP Gasket 327 NP Magnetic Circuit 329 (also order National Overlay Index 330) 329A 329B 330 Operator Panel Overlays 330 332 369 41U2329 Washer Lock D. 3.2 (Misc. Kit item 25) 376 08H7355 Screw M3x8 (Misc. Kit item 15) 382 391 08H7355 Screw, M4x8 (Misc. Kit item 10) | |
15 19 39 63H6349 Bracket Assembly, Printhead Cable with M4x6 Screw 40 55 08H7355 Screw M4x (Misc. Kit item 19) 56 08H7355 Screw M4x14 (Misc. Kit item 2) 57 41U2329 Washer (Misc. Kit item 8) 60 74 NP Fastener Loop Self-Lock 103 41U2329 Washer Internal Teeth (Misc. Kit item 24) 106 NP Ribbon Cartridge (Orderable as consumable) 109 NP Fastener Loop Self-Lock 114 181 182 182A 192 195 08H7355 Screw M4x6 Flat Head (Misc. Kit item 23) 199 NP Fastener Loop Self-Lock 297 298 08H7355 Screw M3x6 (Misc. Kit item 1) | |
16- Tractor asms. 1 (rear tractor when a second tractor is installed). This tractor is installed at the factory on all machines. In a single tractor machine the base tractor is the front tractor. The base tractor becomes the (rear tractor when a second (optional) tractor is installed. 2 (optional, becomes front tractor). This tractor can be installed in front of the base tractor as an option. In a two tractor machine the second (optional) tractor is the front tractor and the base tractor becomes the rear tractor. |