Printek FM8000 FM8003 Parts
Please call for parts assistance
1 4264 Front Base 2 90714 Paper Door 2A 4483 Hinge 2B 4520 Hinge Anchor 2C 4501 Magnet 3 4738 Left Base 4 4730 Right Front Cabinet Support Bracket 6 7 4737 Right Side Base 9 4720 Upper Corner Brace 9A 4707 Lower Corner Brace 10 4731 Right Rear Cabinet Support Bracket 10A 4732 Left Rear Cabinet Support Bracket 11 12 4482 Right Hinge Body 13 4489 Latch 14 4037 Card Guide 15 4742 Control Panel Extrusion 16 4376 Control Panel Plate 17 18 4480 Left Hinge Body 19 90799 Left Trim Plate 20 21 4583 Spacers 22 4521 Ground Clip 23 24 24A 4351 Hinge (included in 90713) 24C 4740 Spring (included in 90713) 24D 2390 Screw (included in 90713) 24E 4523 Nut (included in 90713) 25 26 4584 Left Stiffener Bracket 27 4585 Right Stiffener Bracket 28 4733 PCB Enclosure Bracket 29 4152 Interlock Switch 30 4033 Transformer 120V 30A 4142 Transformer 240V 31 32 4364 Long PCB Guide 33 4365 Short PCB Guide 35 4736 Interlock 36 4272 Paper Exit Bracket 38 (8003) 39 (8003) 40 4363 Transformer Bracket 41 42 4278 PWA Access Panel 43 4462 I/O Option Plate 44 4032 AC Receptacle / Filter 45 4020 Fuse 3.15A SB (for 120 V printer) 45A 4143 Fuse 2A SB (for 240 V printer) 46 4572 Wire Guide 47 4639 Hinge Plate 48 4640 Block 49 4116 Ground Strap 50 4709 Rubber Feet 51 85 Rubber Pads 52 4694 Support Rod 53 4541 Foam 401 4447 #8B x .750 Square Drive B k 402 2276 8-32 .250 PPH Zn 403 4578 8-32 x .250 HWH Zn 404 2278 #8-BT x .500 HWH Zn 407 1066 Nut 8-32 Hex Cptv Lockwasher 408 1321 8-32 x .375 PPH Zn 409 4577 Spacer, Tear Bar Pivot 410 2331 8-AB x 1.000 HWH Zn 411 270 6-32 x .250 PPH Zn 412 373 4-40 x .250 PPH Blk Zn 413 1240 Ring E1000 .188 x .025 St 414 4589 8-B x 1/4 HWH Zn 415 2918 6-32 x 1/4 Triob HWH Slotted 416 1378 6-32 x .500 PPH Zn 417 524 Nut 6-32 Hex Cptv Lckwshr 418 2918 6-32 x 1/4 Triob HWH Slotted 419 268 Nut Hex 6-32 x 1/4AF 3/32 Thk Zn 420 2694 Screw 4-40 x 5/8 PPH Zn 421 652 Whsr Lck #8 Ext 422 2802 Nut 4-40 Hex Cptv Lckwshr 423 4739 8-32 x .312 PH FH Zn 424 4578 8-32 x .250 HWH Zn 425 2922 8-32 x 1/4 Triob HWH Slotted 426 4702 6-32 x 5/16 Triob PPH | |
1 4215 Shuttle Guide Bracket 1A 475 Left Front Shuttle Guide Bracket 2 4216 Shaft 3 4206 LH Pivot Plate 4 90736 RH Pivot Plate 5 2398 Paper Drive Bushing 6 72 Bearing Cap 7 568 Spring 8 4463 Mylar (see inset) 9 10 90721 Tractor Assembly 852si 862 4500se 4503se 4600 4603 852si/862 bottom tractor assembly only. Fully refurbished with 90-day warranty 90721 (set) $68.00 11 4528 Paper Guide 12 4212 Shaft (Round) 13 4210 Shaft (Square) 14 4260 Tractor Support 15 4211 Shaft (Round) 16 4209 Shaft (Square) 17 4786 Tractor Support 18 19 4207 Lever 20 4330 Spring 21 2425 Spacer 22 23 2829 Tractor Gear 24 2079 Oilite Bearing 25 26 27 28 4620 Paper Drive Bushing 29 30 2752 Cable Clamp 31 4884 Front Bracket 32 4915 Grommet 33 4506 Spacer 34 1042 Ground Strap 35 4257 Lower Plate 36 4439 Spring 37 4258 Upper Plate 38 4240 Oilite Bearing (see inset) 39 2066 Pulley 40 41 42 3048 Idler Pulley (included in 90697) 43 4245 Idler Bracket (included in 90697) 44 4235 Floor Tray 45 2966 Cable Clamp 46 4519 Lower Entry Throat Bracket 47 4230 Ribbon Tray 48 4293 Ribbon Latch Block 49 50 1989 1/2" Shaft 51 2894 5/8" Shaft 52 90706 Paper Motion Detector 53 4308 Paper Motion Bracket '54 4705 Plate Extrusion 55 4706 Platen 56 * Left Side Plate 57 58 59 4753 Gap Gear 60 4237 Spacer 61 4515 Cam Lever 62 2395 Gap Spring 63 4759 Linkage 64 4758 Linkage 65 4296 Transfer Linkage 65A 4298 Transfer Shaft 66 2334 Gear 67 4488 Cable Tie Anchors 68 90796 Y-Bracket, Left 68A 90795 Y-Bracket, Right 69 4437 Cutter Mounting Bracket 70 71 4340 Paper Drive Gear 72 2828 Pinch Roller Gear 73 4326 Paper Timing Belt 74 4295 Bumper 75 4231 Paper Drive Gear Shaft 77 2953 Bushing 78 4751 Idler Pulley 80 4323 Shuttle Cable Pulley 81 4324 Shuttle Drive Gear 82 90730 Shuttle Drive Belt 83 4484 Upper Throat Bracket 84 4438 Cutter Mounting Bracket 85 * Right Side Plate 86 90703 Motor FM800x (carriage motor, Shuttle motor, Serv) Fully refurbished with 90-day warranty 90703 $249.00 87 4757 Plate 88 4249 Bracket 89 4329 Spring 90 91 92 93 4598 Servo Fan Bracket 94 4750 Spring 95 4883 Rear Plate 96 97 98 Plate (included in 90710) 99 Plate (included in 90710) 100 101 4290 Gear (included in 90733) 102 4300 Pulley (included in 90733) 103 104 4300 Pulley (included in 90732) 105 4311 Roller Drive Belt 106 90797 Tractor Bracket 107 2079 Oilite Bearing 108 109 4590 Spring for Platen 110 4162 Edging 111 4615 Edge Sensor Bracket (see inset) 112 4128 Ground Wire (see inset) 113 2953 Oilite Bearing 114 4751 Bushing 115 90774 Platen Adjustment Block 116 4834 Gap Gear Stop Block 117 4727 Shaft, Round 118 4726 Shaft, Square 119 4746 Shuttle Return Block (included in 90744) 120 4749 Spacer (included in 90744) 121 4678 Cable Bracket * Factory Installation Only 501 4440 6-32 x .375 PPH Zn 502 270 6-32 x .250 PPH Zn 502A 3061 6-32 x 0.312 FH PH Zn 503 2287 6-B x .500 PPH Bk Zn 504 2068 E-Ring 1/4" Flat 504A 4688 E-Ring 1/4" 505 2067 E-Ring 1/4" Bowed 506 1240 Ring E1000 .188 x .025 St 507 2497 External Ring .500 508 1378 6-32 x .500 PPH Zn 509 524 Nut 6-32 Hex Captive Lockwasher 510 1321 8-32 x .375 PPH Zn 511 4574 6-32 x .250 PFHU/cut Zn 512 3057 8-32 x 3/8 Triob PPH 513 4676 Shoulder Screw .250 x 1.250 #10-32 514 2286 Washer Fl .750 x .209 x .050 515 4443 Lockwasher #10 Ext 516 2404 10-24 Nut Hex Zn 517 1471 Whsr Fl .156 x .312 x .062 St 519 3120 8-32 x 1" Slotted Hex Washer Hd 520 4586 Spacer .38 OD x .19 ID x .062 521 2269 6-32 x .750 PPH a 522 2778 Wshr .625 x .139 x .040 Zn 523 554 4-40 x .500 PPH Zn 524 4652 #8-BT x .500 HWH Zn 525 1066 Nut 8-32 Hex Crtv Lckwshr 526 2276 8-32 x .250 PPH Zn 527 4446 8-32 x 1.250 PPH Zn 528 4342 Spacer, Short, Cable Pulley, FPS 529 4341 Spacer, Long, Cable Puley, FP8 530 2270 6-32 x .187 PPH Zn 531 2328 6-32 x .625 FH PH Zn 532 2504 #4-AB x .250 PPH SS 533 373 4-40 x .250 PPH Bk Zn 534 4599 Washer, Wavy .265 ID x .050 OD 536 2266 4-40 x .375 Hex Skt Hd 537 2918 6-32 x 1/4 Triob HWH Slotted 538 261 4-40 x .375 PPH Bk Zn 540 3052 Screw 4-40 x .3125 PPH Zn 541 465 4-40 x .187 PPH Zn 542 2691 Screw .250-20 x .375 Skt Cap 543 4677 #12 Flat Washer .250 x .562 x .065 544 1932 Spacer Round Stepped .187 x .445 CRS 545 276 Washer F1 .188 x A38 x .049 St 546 375 8-32 x .500 PPH Zn 547 2949 5/8" Wavy Washer 548 2286 Washer F1 .750 x .209 x .050 549 2950 5/8" Push-On Retainer Ring 550 2954 Rubber O-Ring 1/2" x .070 551 2955 Teflon Washer 1/2 x 5/8 x .005 552 2519 813T x .375 Truss Head PH Zinc 553 2225 Shoulder Screw .375 554 4684 Retainer Ring 555 326 6-32 x .375 PPH Blk Zn (included in 90744) 556 4748 Spring 3/16 OD x 9/16 L (included in 90744) 557 267 #6 Lockwasher 558 652 #8 Lockwasher 559 2278 #8BT x 0.500 Hex Head 560 4679 6-32 x 7/8 FH PH 561 4925 E-Ring 1/4" | |
90653 Forms Cutter FormsMaster 8XXX Field Kit New 90653 (New) Retired, no longer available: Contact for alternatives 1 4469 Solenoid (For JA serial number cutters, included in 90780) 1 A 4849 Solenoid (For JB serial number cutters, included in 90788) 2 4783 Roll Pin (included in 90780) 3 4805 Spring (included in 90780) 4 4180 Solenoid Cable Harness (not shown) 5 4399 Throat Open Link (included in 90780) 6 4397 Solenoid Linkage (For JA serial number cutters, included in 90780) 6A 4858 Solenoid Linkage (For JB serial number cutters, included in 90788) 7 4791 Guide Rails 8 90782 Blade Sensor Board 9 2603 Blade Guide Block 10 4831 Finger Guard 11 N/A Lower Blade 12 N/A Upper Blade 13 2910 Captive Screw 10-32 x 2.0 (included in 90776) 14 2909 Cutter Spring Sleeve (included in 90776) 15 4761 Cutter Blade Spring (included in 90776) 16 4808 Shaft Assembly 17 4386 Blade Limit Encoder 18 2916 Idler Roller 19 4817 Idler Roller Pin 20 21 22 2135 Bearing 23 4502 Alignment Pin 24 4806 Left Side Bracket 25 4417 Pinch Roller Belt (LH Side) 26 1649 Pulley 27 2079 Bearing 28 4853 Cutter Pivot Mount Plate 29 4778 Pivot Plate Mounting Spacer 30 4807 Ride Side Plate 31 4780 Sprocket 32 2630 Chain 33 4418 Timing Belt 34 4471 Bearing 35 4404 Top Drive Roller 36 4405 Lower Drive Roller 37 4803 Pinch Roller, Backup, Lower 38 4776 Pinch Roller, Backup 39 4842 Rear Throat Bracket (included in 90775) 40 4839 Blade Cover Bracket (included in 90775) 41 1618 Ted Pad (included in 90775) 42 4821 Snap Latch Plunger (included in 90775) 43 4822 Snap Latch Grommet (included in 90775) 44 4804 Solenoid Bumper Pin 45 90785 LH Mounting Bracket 46 4793 Exit Roller Bracket 47 4794 Exit Roller Spacer 48 4394 Back 49 2396 Rectangular Grommet 50 4777 Installation Handle 51 52 4476 Handle Extrusion 53 4797 Top Exit Throat Bracket 54 4799 Exit Roller Plate 55 4795 Left Exit Throat Block 56 4796 Right Exit Throat Block 57 90784 Right Hand Mounting Bracket 58 4611 Sprocket 58A Set Screw (Part of Sprocket #58) 59 4113 Cable Tie Clip 60 90789 Blade Cover Interlock Switch 61 90787 Right Hand Pivot Bracket 62 90786 Left Hand Pivot Bracket 63 4823 Spacer Bar (not shown) 64 4178 Flat Cable (not shown) 65 527 Stick on Cable Clamp (not shown) 66 4760 Paper Basket (not shown) 67 4864 Paper Basket Back Stop (not shown) 68 4815 Bracket, Paper Support (not shown) 69 4816 Snap, Paper Support Bracket (not shown) 70 4874 Bumper (not shown) 501 1240 E-Ring .188 x .025 502 2283 10-32 x .250 PPH 503 2286 Washer .753 x .209 x .050 504 2068 E-Ring 1/4" Flat 505 4599 Wavy Washer .265 ID x .500 OD 506 2425 Plastic Spacer 507 1321 8-32 x .375 PPH ZN 508 3110 Grommet 509 2329 6-B x .375 PPH ZN 510 2276 8-32 x .250 PPH ZN 511 270 6-32 x .250 PPH ZN 512 2390 8-32 x .375 FH PH ZN 513 4919 #8A x .0750 F/SQ DR BLK 514 270 Screw for Solenoid 4469 (JA) 4850 Screw for Solenoid 4849 (JB) 515 2270 6-32 x .187 PPH ZN 516 4784 Blade Sensor PCB Spacer 517 4441 6-32 x .250 PFH ZN 518 4820 E-Ring 519 1141 8-AB x .750 HWH ZN 520 2642 Shoulder Screw .25 Dia .187 L 521 4830 Spacer 3/8 OD x .194 ID x 3/16 522 4848 Spacer 1/4 OD x .141 ID x 1/4 523 2697 10-32 x .625 Skt Cap 524 2690 10-32 x .375 Skt Cap 525 524 Nut 6-32 Hex Captive Lockwasher 526 2691 .250 -20 x .375 Skt Cap 527 554 4-40 x .500 PPH ZN 528 2288 Washer Fl .125 x .437 x .030 529 2916 Idler Roller 530 2917 Standoff 531 4843 Wavy Washer .50 ID x .68 OD 532 4410 No Longer Used 533 1471 Washer Used With Solenoid 4469 (JA) 2288 Washer Used With Solenoid 4849 (JB) 534 4781 Captive Screw 535 4827 2B x 0.625 PPH Screw 536 2815 1/4-20 x 0.375 Cup Pt. Screw (Set Screw) 537 4878 Screw Bumper (not shown) 538 966 Washer Bumper (not shown) |