IBM Infoprint 1880 MFP 4568

 
 
 
 


IBM Infoprint 1880 Printer
4568-FD1 256 MB standard memory, 80 GB hard disk Standard, Two Standard 550-sheet drawers, and StapleSmart standard media outputs.
IBM Infoprint 1880 Printer
4568-TF1 256 MB standard memory, 80 GB hard disk Standard, Three Standard 550-sheet drawers, and StapleSmart standard media outputs.
IBM Infoprint 1880 Printer
4568-BD1 256 MB standard memory, 80 GB hard disk Standard, Two Standard 550-sheet drawers, and 4-Bin Mailbox standard media outputs.
IBM Infoprint 1880 Printer
4568-TB1 256 MB standard memory, 80 GB hard disk Standard, Three Standard 550-sheet drawers, and 4-Bin Mailbox standard media outputs.
IBM 4568-FD1 InfoPrint 1880 MFP Printer
Fully refurbished with 90-day warranty
4568-FD1 39V3069
$999.00


IBM 4568-TF1 InfoPrint 1880 MFP Printer
Fully refurbished with 90-day warranty
4568-TF1 39V3070
$1499.00


IBM 4568-BD1 InfoPrint 1880 MFP
New
4568-BD1 39V3073 (New)

Retired, no longer available: Contact for alternatives


IBM 4568-TB1 InfoPrint 1880 MFP
New
4568-TB1 39V3074 (New)

Retired, no longer available: Contact for alternatives


Looking for IBM Infoprint 1880 Parts?
4568 InfoPrint 1880 MFP

This monochrome laser multifunction printer (MFP) offers printing of up to 55 pages per minute (ppm)(1) on letter media and up to 53 ppm (1) on A4 media. It offers scanning at up to 55 sides per minute (simplex)(2).

Other benefits of the InfoPrint 1880 MFP include:

  • Integrated duplex and a single-pass duplex color scanner
  • 75 page automatic document feeder (ADF) with improved reliability
  • Built-in "your eyes only" security for confidential and held jobs
  • Customizable 229-mm (9-in) color touch screen and number keypad with control buttons
  • Extra high yield toner cartridges
  • Finishing options including multibin mailbox and StapleSmart finisher

39V3598
39V3598 Pick Roll (2) 300,000
39V3598 Pick Roll (Set of 2)
New
39V3598 (New)
$21.00


39V2967
39V2967 Use and Return Program Toner Cartridge 7,000
39V2967 Return Program Toner Cartridge
New
39V2967 7K Page Yield (New)
$138.00


39V2968
39V2968 High Yield Toner Cartridge 25,000
39V2968 High Yield Toner Cartridge
New
39V2968 25K Page Yield Compatible (New)
$227.00


39V2969
39V2969 Use and Return Program High Yield Toner Cartridge 25,000
Sale39V2969 1850 1860 1870 1880 MFP High Yield Toner Cartridge
New
39V2969 25K Page Yield Compatible (New)
$227.00 $179.00


39V2971
39V2971 Use and Return Program Extra High Yield Toner Cartridge 36,000


Sale39V2971 High Yield Toner Cartridge (1870/1880 MFP only)
New
39V2971 36K Page Yield Compatible (New)
$249.00 $189.00


75P6997
75P6997 Staple refill sets 5,000 x 3
75P6997 Staple Cartridge
New
75P6997 3 x 5000 (New)
$89.00


39V3589
39V3589 ADF Maintenance Kit
Separator Roller, Access cover pick/feed mechanism 120,000
39V3589 ADF Maintenance Kit
New
39V3589 120K Page Yield (New)
$135.00


39V3604
39V3604 Transfer Roll 300,000
39V3604 Transfer Roll 300000
New
39V3604 (New)
$40.00


39V3599
39V3599 Charge Roll 300,000
39V3599 Charge Roll 300000
New
39V3599 (New)
$47.00


39V3600
39V3600 Fuser (LV: 110V) 300,000
39V3600 IBM Fuser Assembly 110V
New
39V3600 (New)
$299.00





39V3600 IBM Fuser Assembly 110V
Fully refurbished with 90-day warranty
39V3600
$145.00


39V3602 Fuser with detack Fingers (LV: 110V) 150,000
39V3602 Fuser with Detach Fingers (LV: 110V)
New
39V3602 150K Page Yield, Advanced Exchange (New)
$332.00


39V3590
39V3590 Maintenance Kit (LV: 110V):
Fuser, Transfer roll, Charge roll, 6 Pick rolls 300,000
39V3590 IBM Fuser Maintenance Kit 110V
New
39V3590 (New)
$319.00





39V3590 IBM Fuser Maintenance Kit 110V
Fully refurbished with 90-day warranty
39V3590
$190.00


39V2693
39V2963 550-Sheet Drawer

39V2965
39V2965 Envelope Feeder
39V2965 Envelope Feeder
New
39V2965 (New)
$345.00


39V2956
39V2956 550-Sheet Tray
39V2956 550-Sheet Tray
Fully refurbished with 90-day warranty
39V2956
$49.00


39V2957
39V2957 2,000-Sheet


39V2957 2000-Sheet Drawer (requires 39V3588)
Fully refurbished with 90-day warranty
39V2957
$249.00


39V2959
39V2959 200-Sheet Universally Adj Drawer


39V2960
39V2960 200-Sheet Universally Adj Tray

39V2961

39V2961 400-Sheet Universally Adj Drawer

39V2962
39V2962 400-Sheet Universally Adj Tray

Ram

39V2693 IPDS & SCS/Tne
39V2693 IPDS & SCS/Tne
New
39V2693 (New)
$442.00



39V2693 Card for IPDS & SCS/Tne
Fully refurbished with 90-day warranty
39V2693
$299.00


39V3463

39V3463 Decryption Card
39V3463 Decryption Card
New
39V3463 (New)
$190.00


Ram

39V3464 Bar Code Card
39V3464 Bar Code Card
New
39V3464 (New)
$322.00


Ram

39V3415 256 MB Memory
39V3415 Infoprint Brand 256 MB Memory
New
39V3415 (New)
$505.00



39V3415 256 MB Memory
New
39V3415 Compatible (New)
$66.00


39V3416

39V3416 512 MB Memory
39V3416 512 MB DDR2 Memory
New
39V3416 Compatible (New)
$123.00



39V3416 512 MB DDR2 Memory
Fully refurbished with 90-day warranty
39V3416
$125.00


Ram

39V3417 1024 MB Memory
39V3417 Infoprint Brand 1024 MB Memory
New
39V3417 (New)
$661.00



39V3417 1024 MB Memory
New
39V3417 Compatible (New)
$152.00


Ram

39V3593 256 MB Flash Memory


39v3593 256 MB Flash Memory
Fully refurbished with 90-day warranty
39v3593
$186.00


39V3420
39V3420 80 GB Hard Disk
39V3420 80 GB Hard Disk
New
39V3420 (New)
$299.00


39V3608
39V3608 Ethernet 1000BaseTX

39V1524
39V1524 Ethernet 10/100BaseTX (1 USB port)

39V1525 Ethernet 1000BaseTX (4 USB ports)
75P685475P6854 802.11g Wireless to USB
39V3623
39V3623 802.11b/g/n Wireless Print Server

39V3423
39V3423 Parallel 1284-B Interface
39V3423 Parallel 1284-B Interface Card
New
39V3423 (New)
$149.00


39V3424
39V3424 RS-232C Serial Interface Card
39V3424 RS-232C Serial Interface Card
New
39V3424 (New)
$199.00


75P7029
75P7029 10 ft. Parallel Cable
75P7029 10 ft. Parallel Cable
New
75P7029 (New)
$19.00


75P7030
75P7030 2-meter USB Cable
75P7030 2-Meter USB Cable
New
75P7030 (New)
$15.00


39V3615
39V3615 5 in. Spacer
39V3615 5 in. Spacer
New
39V3615 (New)
$190.00



39V3615 5 in. Spacer
Fully refurbished with 90-day warranty
39V3615


39V3588
39V3588 Caster Base
39V3588 Caster Base
New
39V3588 (New)
$423.00



39V3588 Caster Base
Fully refurbished with 90-day warranty
39V3588
$266.00


Ram
39V3618 Korean Font Card
39V3618 Korean Font Card
New
39V3618 (New)
$176.00


Ram
39V3619 Simplified Chinese Font Card
39V3619 Simplified Chinese Font Card
New
39V3619 (New)
$176.00


Ram
39V3620 Traditional Chinese Font Card
39V3620 Traditional Chinese Font Card
New
39V3620 (New)
$176.00


Ram
39V3621 Japanese Font Card
39V3621 Japanese Font Card
New
39V3621 (New)
$176.00



Abstract

The 4568 from InfoPrint Solutions Company, a Ricoh-IBM joint venture, is the InfoPrint 1880 multifunction printer (MFP).

Model Abstract 4568-FD1

The 4568 InfoPrint 1880 MFP Model FD1 has a 256 MB standard memory, 1280 MB maximum memory, 80 GB hard disk Standard, 600 MHz processor, Two Standard 550-sheet drawers, and StapleSmart standard media outputs.

Model Abstract 4568-TF1

The 4568 InfoPrint 1880 MFP Model TF1 has a 256 MB standard memory, 1280 MB maximum memory, 80 GB hard disk Standard, 600 MHz processor, Three Standard 550-sheet drawers, and StapleSmart standard media outputs.

Model Abstract 4568-BD1

The 4568 InfoPrint 1880 MFP Model BD1 has a 256 MB standard memory, 1280 MB maximum memory, 80 GB hard disk Standard, 600 MHz processor, Two Standard 550-sheet drawers, and 4-Bin Mailbox standard media outputs.

Model Abstract 4568-TB1

The 4568 InfoPrint 1880 MFP Model TB1 has a 256 MB standard memory, 1280 MB maximum memory, 80 GB hard disk Standard, 600 MHz processor, Three Standard 550-sheet drawers, and 4-Bin Mailbox standard media outputs.


Highlights

This monochrome laser multifunction printer (MFP) offers printing of up to 55 pages per minute (ppm)(1) on letter media and up to 53 ppm (1) on A4 media. It offers scanning at up to 55 sides per minute (simplex)(2).

Other benefits of the InfoPrint 1880 MFP include:

  • Integrated duplex and a single-pass duplex color scanner
  • 75 page automatic document feeder (ADF) with improved reliability
  • Built-in "your eyes only" security for confidential and held jobs
  • Customizable 229-mm (9-in) color touch screen and number keypad with control buttons
  • Extra high yield toner cartridges
  • Finishing options including multibin mailbox and StapleSmart finisher

Note: (1) Exact print speeds vary depending on document complexity, system configuration, software applications, driver, and printer status.

Note: (2) Exact scan speeds vary depending on document attributes, system configuration, and user-selected settings.


Description

InfoPrint 1880 MFP is a new monochrome laser multifunction printer (MFP). The time to first print is as fast as 9.5 seconds. The InfoPrint 1880 MFP includes the following models:

 Standard Standard
Standard Maximum 80 GB 550-sheet media
Model memory memory hard disk Processor drawers outputs
----- -------- ------- --------- --------- --------- --------------
fd1 256 MB 1280 MB Standard 600 MHz Two StapleSmart
tf1 256 MB 1280 MB Standard 600 MHz Three StapleSmart
bd1 256 MB 1280 MB Standard 600 MHz Two 4-Bin Mailbox
tb1 256 MB 1280 MB Standard 600 MHz Three 4-Bin Mailbox


Models fd1 and bd1 include two 550-sheet drawers and a 100-sheet multipurpose feeder for a total input capacity of 1,200 sheets standard. Up to four optional input drawers are supported for a maximum input capacity of 2,300 sheets.

Models tf1 and tb1 include three 550-sheet drawers and a 100-sheet multipurpose feeder for a total input capacity of 1,750 sheets standard. Up to three optional input drawers are supported for a maximum input capacity of 2,300 sheets.

Maximum output capacity for models fd1 and tf1 is 1,050 sheets. Maximum output capacity for models bd1 and tb1 is 950 sheets. Duplex printing is standard on all models of the InfoPrint 1880 MFP.

Memory

All models have one slot for additional SDRAM memory. Memory options for the printer include 256 MB, 512 MB, or 1024 MB memory DIMMs. All models have one slot for the optional 256 MB flash memory card or font cards.

Network connections

All models include internal Ethernet 10/100BaseTX as standard.

The internal wireless feature allows the printer to be connected directly to a wireless LAN. This supports the IEEE 802.11b, 802.11g, and 802.11n draft 2.0 standards. Draft 2.0 refers to the version of the not-yet-ratified IEEE 802.11n standard.

Usage rates

The maximum monthly usage for the InfoPrint 1880 MFP is 275,000 impressions. InfoPrint Solutions Company does not recommend printing to the monthly maximum on a consistent basis.

Print quality

Print resolutions supported by the printer are:

  • 1200 x 1200 dpi
  • 2400 image quality
  • 1200 image quality
  • 600 x 600 dpi
  • 300 x 300 dpi

The Toner darkness setting offers 10 user-selectable settings to balance print darkness and toner savings. The higher the setting, the darker the print (that is, level 1 is the lightest). The printers are shipped with a default setting of 8. From level 8 to level 1 offers up to 50% toner savings, thus reducing the cost of printing. The toner darkness setting is available through the operator panel under the Quality menu and also accessible from the print driver.

Font support

The InfoPrint 1880 MFP printer resident fonts include support for following:

Emulation Number of scalable fonts Number of bitmapped fonts
------------ ------------------------ -------------------------
PCL 6 89 2
PostScript 158 0
PPDS 39 5


The fonts in the PCL emulation are compatible with the fonts in the HP LaserJet 4550 and include nine additional fonts and many extra symbol sets to support extra languages and applications. Included in the PCL emulation are OCR-A, OCR-B, and Code 3 of 9 barcode fonts. The fonts in the PostScript emulation are compatible with all 136 fonts in Adobe PostScript 3 and include 22 additional fonts.

Additional fonts can be downloaded to the printer RAM, optional user flash, or the hard disk.

Included on the CD-ROM shipped with the printer are screen fonts to match the printer's resident scalable fonts. The Software and Documentation CD also include a variety of downloadable fonts for Hebrew and Arabic.

MFP

Scanner
------------------------------------------------------------------------
Scanner Type Color Flatbed with ADF
Scan Technology Charge Coupled Device (CCD)
Light Source Xenon
Number of Light Sources Two

Scanner ADF
------------------------------------------------------------------------
ADF Type Single pass duplex scan, C-Path
Scanner ADF Document Input 75 sheets 20 lb. (75 gsm) paper
& Output Capacity
Scanner Media Depth Max. .15 mm
(thickness) Min. .05 mm
Scanner Media Weight Max. 32 lb (120 gsm)
Min. 14 lb (52 gsm)
Scan Speed Up to 55 sides per minute (simplex)
Color Scan Resolution A4, Officio, Letter, Legal, Folio all 300 dpi
A5, JIS-B5, Executive, Statement all 400 dpi
A6, 4x6, 3x5, Business card all 600 dpi
Document Size Max. 8.5 x 14.0 in (216 x 355 mm) SEF
Min. 3.0 x 5.5 in (114.3 x 139.7 mm) SEF
Document Size Sensing Yes - length and width in ADF
Document Sensing Yes - ADF paper present LED and on/off
settable beep

Scanner Flatbed
------------------------------------------------------------------------
Max Document Size 8.5 x 14.0 in (216 x 355.6 mm) SEF
Document Size Sensing Yes - paper length sensing only on flatbed

Print Engine
------------------------------------------------------------------------
Print Technology Mono Laser
Duplex output Standard
Paper Feed Orientation Short Edge Feed

Fax
-------------------------------------------------------------------------
Modem Built-in Group 3 compatible, Full Function
Fax 33,600 bps, Max V.34 Half Duplex


Features

The printer supports the following features:

Part
number Description
------- -----------------------------------
39V2963 550-Sheet Drawer
39V2965 Envelope Feeder
39V2693 IPDS & SCS/Tne Card
39V3463 Decryption Card
39V3464 Bar Code Card
39V3415 256 MB Memory
39V3416 512 MB Memory
39V3417 1024 MB Memory
39V3593 256 MB Flash Memory
39V3608 Ethernet 1000BaseTX
39V1524 Ethernet 10/100BaseTX (1 USB port)
39V1525 Ethernet 1000BaseTX (4 USB ports)
75P6854 802.11g Wireless to USB
39V3623 802.11b/g/n Wireless Print Server
39V3423 Parallel 1284-B Interface Card
39V3424 RS-232C Serial Interface Card
75P7029 10 ft. Parallel Cable
75P7030 2-meter USB Cable
39V3615 5 in. Spacer
39V3588 Caster Base
39V3618 Korean Font Card
39V3619 Simplified Chinese Font Card
39V3620 Traditional Chinese Font Card
39V3621 Japanese Chinese Font Card


Accessibility by people with disabilities

For hardware offerings:

The following features support use by people with disabilities:

  • Controls and latches are operable with one hand and minimal dexterity.
  • Keys are discernible by touch without activating them.
  • The display, controls, latches, and levers are accessible to someone in a wheel chair.
  • Color is used as an enhancement for conveying information, as well as an additional method of distinguishing between buttons, controls, and latches.


Models

Model Summary Matrix

ModelsStandard MemoryMaximum Memory80 GB Hard DiskProcessorStandard 550-sheet DrawersStandard Media Outputs
fd1256 MB1280 MBStandard600 MHzTwoStapleSmart
tf1256 MB1280 MBStandard600 MHzThreeStapleSmart
bd1256 MB1280 MBStandard600 MHzTwo4-bin Mailbox
tb1256 MB1280 MBStandard600 MHzThree4-bin Mailbox

Customer Setup (CSU)

All products in this announcement are customer setup.


Performance Specifications

The InfoPrint 1880 MFP maximum print speeds are shown in the following table. Actual performance depends on:

  • Interface to the host (parallel, USB or network)
  • Host system and application
  • Page complexity and content of the page
  • Certain printer options installed or selected with the printer
  • Available memory in the printer
  • Media size, media type, and tray source
  • Printer resolution

Note the following special cases that may impact print speeds:

  • Nearly narrow media is defined as media that is wide enough to contact the narrow media sensor but is still not wide enough to continuously run at rated speed (but is dependent on media length), i.e., media approximately 170-209mm in width. Examples are: Executive, and Custom Size media whose width falls into this category. IMPORTANT - When using custom size media, it is critical that the user define the actual width via the Paper Menu - Universal Setup on the op panel for best reliability.
  • Narrow media is defined as media that does not contact the narrow media sensor, i.e., media approximately < 170mm in width. *Examples are A5 and custom size media whose width falls into this category.
  • Envelope conditioning (or thumping) is limited to a max 40 ppm process speed for best reliability. Note that if more than 10 envelopes are fed, they will slow even further due to the narrow media requirement.
  • Envelopes in general are fed at a slower speed than other media for best reliability.
Media Width Category Media Width (mm) Page count before slowing down
---------------------- ------------------ ------------------------------
Nearly Narrow 170 - 209 35
Narrow 0 - 169 10
Envelope 0 - 169 10

Media Speed
--------------------- ------
Letter 55 ppm
A4 53 ppm


The table below specifies throughput based on resolution and media size. For a complete range of media sizes supported, see Media Support.

The InfoPrint 1880 MFP time to first print are shown in the following table.

Print Speeds are shown in the following table.

Media Size 1200 DPI
-------------------------------- --------
Time to first print, as fast as
-Time from Standby Mode (sec) 9.5
Simplex thru-put, up to
-Letter (PPM) 55
-A4 (PPM) 53
Duplex sides thru-put, up to
-Letter (SPM) 37
-A4 (SPM) 36


Print Area

The InfoPrint 1880 MFP printable area is limited to within 4.2 mm (0.167 in.) of top, bottom, left or right edges of the media. Any information placed outside this specified printable area will not print.

Media Support

The fd1 and bd1 models comes standard with two 550-sheet paper drawers and a 100-sheet multipurpose feeder.

The tf1 and tb1 models comes standard with three 550-sheet paper drawers and a 100-sheet multipurpose feeder. See table below for standard and maximum media capacities.

Input Media Combinations and Capacities (sheets)

Models fd1, bd1
Opt. Opt.
Std. Std. 550 sht. 550 sht. Total
drawer drawer MPF drawer drawer Capacity
------ ------ --- -------- -------- --------
Standard 550 550 100 1200
Maximum 550 550 100 550 550 2300

Models tf1, tb1
Opt.
Std. Std. Std. 550 sht. Total
drawer drawer drawer MPF drawer Capacity
------ ------ ------ --- -------- --------
Standard 550 550 550 100 1750
Maximum 550 550 550 100 550 2300


Output Media Capacities (sheets)

Models fd1, tf1
Standard StapleSmart Total
Output Bin Finisher Capacity
---------- ----------- --------
Standard 550 500 1050
Maximum 550 500 1050

Models bd1, tb1
Standard 4-Bin Total
Output Bin Mailbox Capacity
---------- ------- --------
Standard 550 400 950
Maximum 550 400 950


Media Size Sensing

The table below outlines automatic sensing function support.

Sensor Description Type Qty
------------------ ---------------------------------------- --------- ---
1.Home Sensor Detect HW failure-carriage not moving Photo 1
to home location. Interrupt
Timing for flatbed scans-performance.

2.ADF paper sent Know paper loaded in ADF to use as Photo 1
present source for job. Reflect
Jam detect-combined with other sensors.
User enhancements-start warming system.
Light paper present LED, sound audible
beep.

3.Interval Jam detect (in particular at POR). Photo 1
Also used for paper length detection. Reflect

4.Paper at ADF Start image capture-front side and back Photo 1
front side CCD side CCD image capture is timed upon Reflect
Module this.
Jam detect-help know where paper is in
ADF paper path.

5.Paper at ADF Jam detect-help know where paper is in Photo 1
back side CCD ADF paper path. Interrupt

6.ADF paper exit Jam detect-help know if paper has not Photo 1
exited ADF paper path Interrupt

7.Flatbed cover Start flatbed length detection. Photo 1
closing Interrupt

8.Flatbed paper Auto-size support-statement, executive, Photo 3
length letter, legal for US; A4, B5, A5, Reflect
folio for Int'l. (No flatbed width
sensors required).

9.ADF length Auto-size support-detect folio versus Photo 1
sensor A4 for Int'l and legal versus letter Reflect
for US-located about 12.2" from leading
edge of paper before any staging occurs.
This is length detection for entire
stack, not per page.

10.ADF width Auto-size support-detect statement, Multi 1
sensor executive, letter widths for US; A4, Contact
B5, A5 widths for Int'l for each page Point
that is scanned. Detection by movement Switch
of paper guides (sensor PCB required).

11.ADF cover Detect user open/close of ADF cover. Photo 1
open Interrupt

12.ADF jam Sensor on backside CCD module access Photo 1
removal door. Interrupt


Input and output source capacities by media types

 Stack Approximate
Source Media Height reference capacity
------------------------------ -------------- ------ --------------------
INPUT
Std. 550-sheet drawer/tray(2) plain paper(1) 55mm 550 sheets (75 gsm)
Opt. 550-sheet drawer/tray(2) transparencies 450 transparencies
labels 200 labels (3)


Envelope Feeder (2,5) envelopes 64.7mm 85 envelopes (75gsm)

Multipurpose tray (2) plain paper 10mm 100 sheets (75 gsm)
envelopes 10 envelopes (75gsm)
other various quantities
(4)

Scanner ADF plain paper, 12mm 75 sheets (20 lb)
other

OUTPUT
Std. 500-sheet output bin plain paper(1) 85mm 550 sheets (75 gsm)
(1,2) transparencies 300 transparencies
labels 200 labels (3)
envelopes 50 envelopes (75gsm)

4-bin mailbox option (1,2) plain paper(1) 15mm 100 sheets per bin
envelopes N/A

StapleSmart II finisher (1,2) plain paper(1) 500 sheets (75 gsm)

Note: (1) 20 lb. xerographic paper at ambient environment

Note: (2) Capacity may vary and is subject to media specifications and printer operating environment

Note: (3) Capacity will vary with label material and construction

Note: (4) Capacity will vary depending on weight and type media

Note: (5) Stack height will not reach maximum due to weight of envelopes on one side of option tray causing tilt in tray

Note: (6) This is an estimate based on the capacity of the standard 550-sheet

Media Sizes Supported

Input Media for InfoPrint 1880 MFP

The "Universal" setting allows the user to use custom sizes up to the maximum specified. There are limitations with the "Universal" setting in that duplexing, rotation of images, and n-up may not work since the printer does not know the exact size of the paper.

 Opt
Std 550
Media tray tray MFP
------------------------------------ ---- ---- ---
A4 210x297 mm/8.27x11.7 in. Yes Yes Yes
A5 148x210 mm/5.83x8.27 in. Yes Yes Yes
JIS-B5 182x257 mm/7.17x10.1 in. Yes Yes Yes
Letter 215.9x279.4 mm/8.5x11 in. Yes Yes Yes
Legal 215.9x355.6 mm/8.5x14 in. Yes Yes Yes
Executive 184.2x266.7 mm/ Yes Yes Yes
7.25x10.5 in.
Folio 215.9x330.2 mm/8.5x13 in. (1) Yes Yes Yes
Statement 139.7x215.9 mm/5.5x8.5 Yes Yes Yes
in. (1)
Universal (2) (3)
139.7 x 210 mm to 215.9 x 355.6 mm/ Yes Yes No
5.5 x 8.27 in. to 8.5 x 14 in.
69.85 x 127 mm to 215.9 x 355.6 mm/ No No Yes
2.75 x 5 in. to 8.5 x 14 in.
148 x 182 mm to 215.9 x 355.6 mm/ No No No
5.83 x 7.17 in. to 8.5 x 14 in.
76.2 x 127 mm to 215.9 x 355.6 mm/ No No Yes
3 x 5 in. to 8.5 x 14 in.
76.2 x 177.8 mm to 215.9 x 355.6 mm/ No No No
3 x 7 in. to 8.5 x 14 in.
7 3/4 Env. No No Yes
98.4 x 190.5 mm/3.875x7.5 in.
9 Env. No No Yes
98.4 x 225.4 mm/3.875x8.9 in.
Commercial #10 Env. No No Yes
104.8 x 241.3 mm/4.12x9.5 in.
DL Env. 110x220 mm/4.33x8.66 in. No No Yes
Other Envelope (5) No No Yes
98.4 x 162 mm to 176 x 250 mm
3.87 x 6.38 in. to 6.93 x 9.84 in.

Media Types
Paper Yes Yes Yes
Cardstock Yes Yes Yes
Transparencies Yes Yes Yes
Paper Labels (4) Yes Yes No
Polyester Labels-Not Supported No No No
Dual web Labels-Not Supported No No No
Integrated Labels-Not Supported No No No
Vinyl Labels-Not Supported No No No

Note: (1) This size does not appear in the paper size menu until tray size sensing is turned off.

Note: (2) This size setting formats the page for 215.9 x 355.6 mm (8.5 x 14 in) unless the size is specified by the software application.

Note: (3) No universal support for the following options: 2000 sheet drawer. all specially designed Print Cartridges for Label Applications.

Note: (4) A5, JIS B5, Exec sizes cannot be stapled.

 Opt
Env.
Media feeder Duplex
------------------------------------------ ------ ------
A4 210x297 mm/8.27x11.7 in. No Yes
A5 148x210 mm/5.83x8.27 in. )4) No Yes
JIS-B5 182x257 mm/7.17x10.1 in. (4) No Yes
Letter 215.9x279.4 mm/8.5x11 in. No Yes
Legal 215.9x355.6 mm/8.5x14 in. No Yes
Executive 184.2x266.7 mm/ No Yes
7.25x10.5 in. (4)
Folio 216x330 mm/8.5x13 in. (1) No Yes
Statement 139.7x215.9 mm/5.5x8.5 No No
in.
Universal (2,3) No No
139.7 x 210 mm to 215.9 x 355.6 mm/
5.5 x 8.27 in. to 8.5 x 14 in.
69.85 x 127 mm to 215.9 x 355.6 mm/ No No
2.75 x 5 in. to 8.5 x 14 in.
148 x 182 mm to 215.9 x 355.6 mm/ No Yes
5.83 x 7.17 in. to 8.5 x 14 in.
76.2 x 127 mm to 215.9 x 355.6 mm/ No No
3 x 5 in. to 8.5 x 14 in.
76.2 x 177.8 mm to 215.9 x 355.6 mm/ No No
3 x 7 in. to 8.5 x 14 in.
7 3/4 Env. Yes No
98.4 x 190.5 mm/3.875x7.5 in.
9 Env. Yes No
98.4 x 225.4 mm/3.875x8.9 in.
Commercial #10 Env. Yes No
104.8 x 241.3 mm/4.12x9.5 in.
DL Env. 110x220 mm/4.33x8.66 in. Yes No
Other Envelope Yes No
98.4 x 162 mm to 176 x 250 mm
3.87 x 6.38 in. to 6.93 x 9.84 in.

Media Types
Paper No Yes
Cardstock No Yes
Transparencies No No
Paper Labels No No

Note: (1) This size does not appear in the Paper Size menu until Tray Size Sensing is turned off.

Note: (2) This size setting formats the page for 215.9 x 355.6 mm (8.5 x 14 in) unless the size is specified by the software application.

Note: (3) No universal support for the 2,000 sheet drawer.

Note: (4) A5, JIS B5, Exec sizes cannot be stapled.

Output Media for InfoPrint 1880 MFP

 Std. Opt.
Output 4-Bin
Media bin Mailbox
------------------------------------ ------ -------
A4 210x297 mm/8.27x11.7 in. Yes Yes
A5 148x210 mm/5.83x8.27 in. (4) Yes Yes
JIS-B5 182x257 mm/7.17x10.1 in. (4) Yes Yes
Letter 215.9x279.4 mm/8.5x11 in. Yes Yes
Legal 215.9x355.6 mm/8.5x14 in. Yes Yes
Executive 184.2x266.7 mm/ Yes Yes
7.25x10.5 in. (4)
Folio 216x330 mm/8.5x13 in. (1) Yes Yes
Statement 139.7x215.9 mm/5.5x8.5 Yes No
in.
Universal (2,3) No No
139.7 x 210 mm to 215.9 x 355.6 mm/
5.5 x 8.27 in. to 8.5 x 14 in.
69.85 x 127 mm to 215.9 x 355.6 mm/ Yes No
2.75 x 5 in. to 8.5 x 14 in.
148 x 182 mm to 215.9 x 355.6 mm/ No No
5.83 x 7.17 in. to 8.5 x 14 in.
76.2 x 127 mm to 215.9 x 355.6 mm/ No No
3 x 5 in. to 8.5 x 14 in.
76.2 x 177.8 mm to 215.9 x 355.6 mm/ No No
3 x 7 in. to 8.5 x 14 in.
7 3/4 Env. Yes No
98.4 x 190.5 mm/3.875x7.5 in.
9 Env. Yes No
98.4 x 225.4 mm/3.875x8.9 in.
Commercial #10 Env. Yes No
104.8 x 241.3 mm/4.12x9.5 in.
DL Env. 110x220 mm/4.33x8.66 in. Yes No
Other Envelope Yes No
98.4 x 162 mm to 176 x 250 mm
3.87 x 6.38 in. to 6.93 x 9.84 in.

Media Types
Paper Yes Yes
Cardstock Yes No
Transparencies Yes No
Paper Labels Yes No

Note: (1) This size does not appear in the Paper Size menu until Tray Size Sensing is turned off.

Note: (2) This size setting formats the page for 215.9 x 355.6 mm (8.5 x 14 in) unless the size is specified by the software application.

Note: (3) No universal support for the 2,000 sheet drawer.

Note: (4) A5, JIS B5, Exec sizes cannot be stapled.

 Optional
StapleSmart
Media output bin
------------------------------------ -----------
A4 210x297 mm/8.27x11.7 in. Yes
A5 148x210 mm/5.83x8.27 in. (4) Yes
JIS-B5 182x257 mm/7.17x10.1 in. (4) Yes
Letter 215.9x279.4 mm/8.5x11 in. Yes
Legal 215.9x355.6 mm/8.5x14 in. Yes
Executive 184.2x266.7 mm/ Yes
7.25x10.5 in. (4)
Folio 216x330 mm/8.5x13 in. (1) Yes
Statement 139.7x215.9 mm/5.5x8.5 in. No
Universal (2,3) No
139.7 x 210 mm to 215.9 x 355.6 mm/
5.5 x 8.27 in. to 8.5 x 14 in.
69.85 x 127 mm to 215.9 x 355.6 mm/ No
2.75 x 5 in. to 8.5 x 14 in.
148 x 182 mm to 215.9 x 355.6 mm/ No
5.83 x 7.17 in. to 8.5 x 14 in.
76.2 x 127 mm to 215.9 x 355.6 mm/ No
3 x 5 in. to 8.5 x 14 in.
76.2 x 177.8 mm to 215.9 x 355.6 mm/ No
3 x 7 in. to 8.5 x 14 in.
7 3/4 Env. No
98.4 x 190.5 mm/3.875x7.5 in.
9 Env. No
98.4 x 225.4 mm/3.875x8.9 in.
Commercial #10 Env. No
104.8 x 241.3 mm/4.12x9.5 in.
DL Env. 110x220 mm/4.33x8.66 in. No
Other Envelope No
98.4 x 162 mm to 176 x 250 mm
3.87 x 6.38 in. to 6.93 x 9.84 in.

Media Types
Paper Yes
Cardstock No
Transparencies No
Paper Labels No

Note: (1) This size does not appear in the Paper Size menu until Tray Size Sensing is turned off.

Note: (2) This size setting formats the page for 215.9 x 355.6 mm (8.5 x 14 in) unless the size is specified by the software application.

Note: (3) No universal support for the 2,000 sheet drawer.

Note: (4) A5, JIS B5, Exec sizes cannot be stapled.

Media Weights

Standard and optional input devices

 Std. trays 1 Env.
Material Type 550-sht drawer MPF feeder
---------- -------------- -------------- -------------- ------
Paper Xerographic or 60 to 176 gsm 60 to 135 gsm N/A
business paper grain long grain long
(16 to 47 lb. (16 to 36 lb.
bond) bond)

Cardstock Index Bristol 163 gsm 120 gsm N/A
maximum (90 lb. bond) (67 lb.bond)
(grain Tag 163 gsm 120 gsm N/A
long)(1) (100 lb. bond) (74 lb.bond)
Cover 176 gsm 135 gsm N/A
(65 lb. bond) (50 lb.bond)
(1,2) (1,2)

Cardstock Index Bristol 199 gsm 163 gsm N/A
maximum (110 lb. bond) (90 lb.bond)
(grain Tag 203 gsm 163 gsm N/A
short)(1) (125 lb. bond) (100 lb.bond)
Cover 216 gsm 176 gsm N/A
(80 lb. bond) (65 lb.bond)

Transpar- Laser printer 138 to 146 gsm 138 to 146 gsm N/A
encies (37 to 39 lb. (37 to 39 lb.
bond) bond)

Labels- Paper 180 gsm 163 gsm N/A
maximum (48 lb. bond) (43 lb. bond)

Envelopes Sulfite, wood- N/A 60 to 105 gsm 60 to
free or up to (16 to 28 lb. 105 gsm
100% cotton bond) (3,4) (16 to
bond 28 lb.
bond) (2,3)

Note: (1) Grain short is preferred for papers over 135 gsm.

Note: (2) 28 lb. bond envelopes are limited to 25% cotton content.

Note: (3) Includes envelopes fed from the multipurpose feeder only.

Additional Media Guidelines for InfoPrint 1880 MFP

Follow the media guidelines below for successful printing:

Paper designed for use with xerographic copiers should provide satisfactory print quality and feed reliability. Other types of supplies may be suitable. It is recommended that users test any particular brand for suitability to their applications. Refer to the printers User's Guide for additional media specifications.

Paper

  • Rough, highly textured, limp, or pre-curled papers will result in lower print quality and more frequent paper feed failures.
  • Colored papers must be able to withstand 220 deg C (446 deg F) fusing temperature.
  • Preprinted forms and letterheads should be selected using guidelines found in the printer User's Guide. The chemical process used in preprinting may render some papers unsuitable for use with these printers.

The following paper types are not recommended for use with the printer:

  • Chemically treated papers used to make copies without carbon paper, also known as carbonless papers, carbonless copy paper (CCP), or no carbon required (NCR) paper.
  • Preprinted papers with chemicals that may contaminate the printer.
  • Preprinted papers that can be affected by the temperature in the printer fuser.
  • Preprinted papers that require a registration (the precise print location on the page) greater than +/-2.3 mm (+/-0.9 in.), such as optical character recognition (OCR) forms. In some cases, registration can be adjusted with a software application to successfully print on these forms.
  • Coated paper (erasable bond) synthetic papers or curled papers
  • Rough-edged, rough or heavily textured surface papers, or curled papers.
  • Recycled papers that fail EN12281:2002 (European).
  • Paper weighing less than 60 gsm (16 lb).
  • Multiple-part forms or documents.

Envelopes

  • If envelope wrinkling occurs refer to the User's Guide for correct loading and stacking of envelopes.
  • All envelopes should be new, unused, and without package damage.
  • Envelopes with excessive curl or twist exceeding 6.0 mm, those stuck together, those with bent corners or nicked edges, or those that interlock should not be used.
  • Minimum weight: 75 gsm (20lb.)
  • The following envelopes should not be used:
    • Envelopes with windows, holes, perforations, cutouts, or deep embossing
    • Envelopes with metal clasps, string ties, or metal folding bars
    • Envelopes with exposed flap adhesive when the flap is in the closed position
  • For best results, printing on new 90 gsm (24 lb.) sulfite or 25% cotton bond envelopes is recommended.
  • Under high humidity conditions (over 60%) the envelopes may seal during printing.

Transparencies

  • Use letter or A4-size sheets only
  • Transparencies specifically designed for xerographic copy machines or laser printers may be used with the InfoPrint 1880 MFP
  • Single-sided transparencies designed for color laser printers may not work well

Recycled paper

As an environmentally conscious company, InfoPrint Solutions Company supports the use of recycled office paper produced specifically for use in laser (electrophotographic) printers. The printers are consistently tested with recycled paper (20-100% post-consumer waste) and a variety of test paper from around the world, using chamber tests for different temperature and humidity conditions. InfoPrint Solutions Company has found no reason to discourage the use of today's recycled office papers, but generally the following property guidelines apply to recycled paper.

  • Low moisture content (4-5%)
  • Suitable smoothness (100-200 Sheffield units)
  • Suitable sheet-to-sheet coefficient of friction (0.4-0.6)
  • Sufficient bending resistance in the direction of feed

Recycled paper, paper of lower weight (<60 gsm / 16 lb bond) and/or lower caliper (<3.8 mils / 0.1 mm), and paper that is cut grain-short for portrait (or short-edge) fed printers may have lower bending resistance than is required for reliable paper feeding. Before using these types of paper for laser (electrophotographic) printing, consult your paper supplier. Remember that these are general guidelines only and that paper meeting these guidelines may still cause paper feeding problems.

Labels

Labels should be selected using guidelines found in the User's Reference, Complete Printer Reference, or the Cardstock and Label Guide and tested for acceptability. Paper labels are supported for occasional use only. VINYL AND POLYESTER LABELS ARE NOT SUPPORTED.

Print Quality

General Statement

Due to the print technology, paper designed for use with xerographic copiers should provide satisfactory print quality and feed reliability. Other types of supplies may be suitable. It is recommended that users test any particular brand for suitability to their applications. Refer to the User's Guide for additional media specifications.

Data Streams

  • PostScript 3 Emulation
  • PCL 6 Emulation
  • XPS
  • PPDS Migration Tool
  • PDF v1.6 emulation
  • HTML
  • Direct Image

Operator Panel

  • Touch sensitive graphical user interface plus 17 "hard" buttons and one LED
  • 9 inch diagonal color LCD touchscreen

USB Direct Interface

Direct USB connectivity allows individuals to print files directly to the printer or scan directly from the MFP using an approved USB flash memory device. Through the printer's USB Direct interface on the printer's operator panel, a user can simply insert the USB flash memory device, select the appropriate file and or select the USB flash memory device as a scan destination.

Direct USB requires a supported USB flash memory device. The following have been tested and approved for USB flash memory devices:

  • Lexar Firefly 512MB
  • Lexar Firefly 1GB
  • SanDisk Cruizer Micro 512MB
  • SanDisk Cruizer Micro 1GB
  • Sony 512MB
  • Sony 1GB

While other USB flash drives have not been tested and therefore cannot be approved by InfoPrint Solutions Company, these products may function if the storage device meets the following qualifications:

  • Supports the USB 2.0 specification, specifically supporting the High Speed mode
  • Use the FAT file system

Fax Features

  • Block Junk Fax Function/Banned Fax List
  • Blocks junk faxes based on caller ID and remote station ID.
  • Caller ID Support
  • Fax Forwarding
  • Incoming faxes may be forwarded to another fax machine, e-mail, FTP.
  • HalfTone
  • Maximum Broadcast locations is 400. Note: each number in a group fax is a location.
  • Group Fax (Broadcasting)
  • Manual Fax
  • Fax from PC
  • Fax from PC is supported using Postscript driver for both local and network attach modes.
  • Fax Shortcuts
  • Maximum characters per shortcut = 512 characters
  • Speed Dials
  • Fax Content
    • Text
    • Text/Photo
    • Photograph
  • Fax Preservation
  • LDAP Lookup

Scan Specific Specifications

Scan Performance

The following table summarizes performance numbers for the InfoPrint 1880 MFP.

  • Scan Speed:
    • Up to 55 sides per minute (simplex)

Scan Features

  • Job Build/Custom job from flatbed or ADF
  • Duplex Scan
  • Mono Output Resolution 600 X 600 dpi (max)
  • Color Output Resolution 600 X 600 dpi (max)
  • USB and Network TWAIN Drivers:
    • For a list of supported operating systems, see Driver tables
  • Scan Destinations
    • USB Thumbdrive
    • E-mail
    • FTP
    • LDSS
    • Network or USB connected computer
    • Window network folder (requires installation of embedded scan to folder application)
  • File Formats:
    • TIFF
    • JPG or JPEG
    • PDF
    • XPS
  • Scan Preview
  • Support Compressions:
    • PDF - 1 bit - JBIG2, CCIT G4, Flate 8/24 bit - Flate, JPEG
    • TIFF - 1 bit - CCIT G4, 8/24 bit - Packbits, LZW
    • JPG - 8/24 bit - JPEG

Copy Specific Specifications

Detailed first copy out times

Monochrome:

Input Mode Size Copy Start State Copy Time(1)
--------- ---------------------- ------ ---------------- ------------
ADF (1) Text or Text/Photo Letter StandBy/Ready 10.5 sec.
ADF (1) Text or Text/Photo A4 StandBy/Ready 10.5 sec.

Flatbed Text or Text/Photo Letter StandBy/Ready 7.5 sec.
Flatbed Text or Text/Photo A4 StandBy/Ready 7.5 sec.

ADF Photo or Printed Image Letter StandBy/Ready 10.5 sec.
ADF Photo or Printed Image A4 StandBy/Ready 10.5 sec.

Flatbed Photo or Printed Image Letter StandBy/Ready 7.5 sec.
Flatbed Photo or Printed Image A4 StandBy/Ready 7.5 sec.

ADF (1) Text/Mixed Letter PowerSaver 10.5 sec.
ADF (1) Text/Mixed A4 PowerSaver 10.5 sec.

Flatbed Text/Mixed Letter PowerSaver 7.5 sec.
Flatbed Text/Mixed A4 PowerSaver 7.5 sec.

Note: (1) Loading paper in the ADF or Flatbed or touching the MFP display will activate warm-up of the MFP and could lower this time to first copy.

Time to First Copy or First Copy Out Time (TTFC or FCOT) - Regardless of using the Flatbed or the ADF this is the amount of time from pressing the Copy button until the preprinted copy sheet lands in the output bin.

Copy Features/Functions

  • Copy Resolution:
    • 600 dpi optical
    • 300 or 600 dpi feed
  • Copy Collation
  • Paper Save Functions (N-Up):
    • 2 Up Portrait
    • 2 Up Landscape
    • 4 Up Portrait
    • 4 Up Landscape
  • Reduced/Enlarge function:
    • 25% to 400%
  • Maximum Number of Copies:
    • 999
  • Margin Shift
  • Separator Sheets
    • Between Pages
    • Between Copies
    • Between Jobs
  • Overlays
  • Duplex output
    • Long edge binding
    • Short edge binding

Fax Specific Specifications

Fax Performance

The following table applies to the fax option card and models with fax standard.

Function Specification
--------------------------- -------------------------------------------
Transmission Speed < 3 seconds per page
Fax storage If a hard disk is installed, faxes are
stored on the hard disk. The fax storage
size is the size of the hard disk less
1 GB. If a hard disk is not installed,
faxes are stored on the flash memory.
The maximum fax storage size on flash
is 18 MB.
Speed Dials Based on 10 digit phone number with a
shortcut limit of 512 characters:
Disk models - 1800
Diskless models - 500
Group Fax 46 locations (based on 10 digit numbers
with a max of 512 characters). Supported
by speed dials (a.k.a. shortcuts) and
user interface panel.
Broadcast 400 locations (each number in a group fax
is a location)
Manual Fax Yes
Fax from PC Supported using PS driver for both local and
network attach modes.
Fax ReDirect E-mail Address 512 characters
Storage


When installed in the MFP, the following specifications are met by the fax card:

Function Specification
--------------------------- -------------------------------------------
Line Connection PSTN or Analog PABX (RJ-11)
ITU Compatibility Group 3 / ECM
Standard Resolution: 200x100 (send) 200x100, 204x98 (receive)
Fine Resolution: 200x200 (send) 200x200, 204x196 (receive)
SuperFine Resolution: 300x300 (send) 300x300, 204x391 (receive)
UltraFine Resolution: 600x600 (send) 400x400, 408x391 (receive)

Modem
Speed - Standard 33,600 bps Max, V.34 Half-Duplex
Error Correction Method ITU T.30
Automatic Train Down Yes
Hand Set No
Communications
The modem satisfies the requirements
specified in ITU-T (CCITT) recommendations
V.34 half-duplex, V.17, V.29, V.27 ter, V.21
and meets the binary signaling requirements
of V.8 and T.30 with annex. F.
Protocol ITU T.30
Modulation Type ITU V.34, V.17, V.29, V.27ter
Tonal Signal ITU V.8, V.21 T.30
Data Compression T.4 1D Modified Huffman encoding
T.4 2D Modified Read encoding
T.6 Modified Read Encoding
T.88 JBIG2
T.81 JPEG
Modem Speeds: 33600, 31200, 28800, 26400, 24000, 21600,
19200, 16800, 14400, 12000, 9600, 7200,
4800, 2400bps
Receive Level: -16dBm -50 dBm
Modem Chipset: Conexant SSF336
Output Level: Adjustable: -1dBm~-35dBm
Initial Setting: Country Dependent

Line Interface Section
Modular Plug: RJ-11C
OutBand Signal Level: Guaranteed North American and Europe PTT
-Insulation
Resistance
(250VDC)
Tip - Ring: Higher than 5 Meg Ohms
Tip - Ring-GND Higher than 5 Meg Ohms
Ring Detection: Complies with all
regulatory requirements
Dialing Characteristics
-Dial Pulse
Not Supported
1) DTMF
Coding Format
1209 Hz 1336 Hz 1477 Hz
697 Hz 1 2 3
770 Hz 4 5 6
852 Hz 7 8 9
941 Hz * 0 #

Retry No Answer 1 Additional Retry
(also if not a fax at the far end)

Busy 0 to 9 Additional Tries
(user programmable, factory default is 5)

Frequency 1 to 200 minutes
(user programmable, factory default is 3 minutes)


Security Features

The MFP's contain several standard and optional features and functions that improve or enhance the security of the device. All security features accessible in previous MFPs have been carried forward to this generation printer family, and many new security features have been added. Below is a list of continued security features and new ones.

Continued security features include:

  • MFP controls, such as password restrictions, user authentification, disabling of device capabilities, protocols and/or network communication paths.
  • MFP touch screen lock function
  • Setting security using the Embedded Web Server (EWS)
  • Setting the system password
  • Using the secure Embedded Web Server
  • Supporting SNMPv3 (Simple Network Management Protocol version 3)
  • Supporting IPSec (Internal Protocol Security)
  • Disabling ports and protocols
  • Using 802.1x Authentification
  • Locking the operator panel menus
  • Printing lockout (only available when a hard disk is installed
  • Encrypting the hard disk
  • Hard disk wiping (available in EC1)
  • Using the restricted server list function
  • Digitally Signed Firmware Update Files

New/Improved security features include:

Advanced Security Improvements
Feature Function Benefit
-------------- ----------------------------- ----------------------------
Custom Access Group based using industry Easily integrates to any
Control standards environment:
Customizable authorization Use current authorization
methods mechanisms as you would
Over 50 access controls adds with a PC.
flexibility Flexible enough to
accommodate new and unique
authentication technologies
More control over who can do
what

Audit Logging Ability to track security Mitigate exposures through
related events (Event types, event tracking:
tracked information, export Proactively track & identify
capabilities, log full potential risks
behavior, digitally sign Easily integrates with your
log files) intrusion detection system
for proactive realtime
tracking

Disk Wiping Residual data removal Flexible residual data
(1) prevents exposure removal:
Automatic, scheduled, or on Protect information from
demand unintentional exposure
According to your own needs
with automatic, scheduled,
or on demand

Validations Satisfy rigorous governmental Satisfies rigorous
standards government standards:
Features through global Verify security features
common criteria independently through common
Cryptography through FIPS criteria
encryption standard Maintain confidentiality
and integrity of information
through FIPS data encryption
standards

Note: (1) Available in EC1.

Security improvements in the hardware:

  • Rear USB-A port access
  • Real Time Clock - Certification management, job expiration, log timestamps, Kerberos ticketing, and scheduled disk wiping (available in EC1)
  • Cartridge Chip
  • Kensington Lock
  • Lockable Input Options

Other security features:

  • Direct USB access control - Ability to use PN/username & password to access port
  • New password reset procedure
  • Password protect hidden/service menus
  • Embedded Web Server (EWS) controls
    • Username added to password
    • Ability to remain static with staff change
    • Expiration time for password
  • Disable LST port
  • Low, Full, High USB Speeds for Authentication
  • Option to lock down USB host port after hours
  • Additional SMTP Authentication protocols (NTLM and MD5 at a minimum)
  • SMTP Authentication based on user ID
  • Separate LDAP search base for authentication & address book
  • Multiple Search Bases for LDAP operations
  • Search for a group in LDAP
  • Limited retries of device passwords
  • Improved password reset security
  • Protect hidden menus with passwords
  • Secure documents (creating and/or printing password protected documents)

Certifications

The InfoPrint 1880 MFP comply with the global safety standard for Information Technology Equipment, IEC 60950, and its country equivalents in the markets we serve. The following sections highlight the approvals and certifications that printer is expected to receive.

100-127V Version

Country
---------------- -------------------------------------------------------
USA, Canada, Energy Star
Canada Canadian Standards Assoc. CAN/CSA-C22.2 No. 60950-1-03,
Information Technology Equipment - Safety - Part 1:
Genral Requirements, deviations D1 & D2
Canada ICES-003, Issue 4, Class A
USA UL 60950-1, Information Technology
Equipment - Safety - Part 1: General Requirements,
deviations D1 & D2
USA U.S. FDA CDRH - Registration - Laser Safety - per
21 CFR Chapter I, Subchapter J, Section 1040
USA IEC 60320 Appliance Couplers for Household and Similar
General Purposes
USA ECMA-74:8th Edition, Annex D
Environmental Certifications
US, Canada Energy Star
Canada Canadian Environmental Choice

Fax Certifications
USA CFR 47, Part 68 - TCB Grant of approval
USA ACMA "A-Tick" mark based on Suppliers Declaration of
Conformity with Electromagnetic Compatibility
Standards as required under the Radiocommunications
Act, AS/ACIF S002:2005, Analogue interworking and
non-interference requirements for Customer Equipment
for connection to the Public Switched Telephone
Network and Safety standard AS/NZS 60950-1:2003
Canada Self Declaration to CS-03

802.11 Wireless Certifications
USA FCC Part 15.27 and other relevant provisions of the Code
of Federal Regulations dealing with intentional radiators
Canada Industry Canada RSS-210, RSS-GEN and RSS-102

Other/Miscellaneous Other country approvals may be obtained

Note: CB Certificate and Test report to include the country differences of all participating CB Scheme members as listed at:

www.cbscheme.com

With the exception of Canada (CA), Japan (JP), and U.S.A. (US). CB assessment shall be to IEC 60950-1:2001

Printer Management Utilities

MarkVision Professional

Available from:

https://www.markvisionprofessional.com

MarkVision Professional is a cross-platform print management solution that enables IT administrators to proactively monitor and manage network devices in an enterprise environment via a web browser or client application. It provides IT administrators with realtime device status and information, centralized device setup, remote printer monitoring and management, and asset management capabilities. These devices are supported by MarkVision Professional v11.2 with no additional plug-ins.

MarkVision Messenger

Available from:

https://www.markvisionprofessional.com

MarkVision Messenger provides real-time notification of printer conditions via e-mail, paging, or other applications and facilitates automated responses to these conditions before they become critical and disruptive to user productivity. MarkVision Messenger enhances administrators' quality for service and improves end-user productivity and satisfaction.

Supported Operating Systems (MarkVision Professional)

Apple Macintosh
Mac OS X 10.4
Microsoft Windows
Windows 2000 Service Pack 4 (SP4)
Windows XP Service Pack 2 (SP2), 32-bit only
Windows 2003 Server Service Pack 2 (SP2), 32-bit only
Windows 2003 Server R2 Service Pack 2 (SP2), 32-bit only
Windows Server 2008, 32-bit
Windows Vista Enterprise
Windows Vista Business
Unix
IBM AIX 5.2, 5.3
HP-UX 11i (11.11)
Sun Solaris SPARC 8, 9, 10
Linux
Red Hat Enterprise Linux (RHEL) ES 4, Client 5
SUSE Linux Enterprise 8, 9, 10


Software Installation and Distribution tools

This Install utility provides a very powerful method to install or uninstall printer software in Windows 2000, Windows XP, or Windows Server 2003 environments. Through the use of the Script Install utility, System Administrators can easily perform mass rollouts of InfoPrint Solutions Company printers by creating custom scripts to perform local or remote printer software installations on end user workstations. When combined with the Driver Profiler utility, I/T shops can centrally create and deploy custom printing environments for each remote location. Together, these utilities drastically reduce the time required to install printer software in a distributed environment.

Printing Solution for Novell systems

This Printing Solution for Novell systems offers administrators more control over InfoPrint Solutions Company printers. This all-inclusive package provides support for both NDPS and iPrint printing systems on NetWare 5.1, 6.0, 6.5 servers and NOES for NetWare servers. The package consists of Novell's NDPS gateway coupled with InfoPrint Solutions Company custom control snap-ins for both NetWare Administrator (NWAdmin) and iManager. By offering custom support for both NetWare Administrator and iManager management utilities, this offering allows administrators to take full control of InfoPrint Solutions Company printers in a Novell printing environment.

Host Software

Windows Systems Drivers

To maximize the user experience, InfoPrint Solutions Company offers system PCL emulation and PostScript emulation drivers for Windows 2000, XP, Server 2003, Vista and Server 2008 platforms. Systems drivers for Windows provide the most comprehensive set of printing features available for InfoPrint Solutions Company products. Offering an easy-to-use interface and time saving preset features, the InfoPrint Solutions Company drivers allow users to access popular features intuitively, while utilizing Microsoft's rendering engine to provide a solid printing experience. InfoPrint Solutions Company Status Messenger replaces the prior status window.

Universal Driver

The InfoPrint Solutions Company Universal Driver packages in PCL and PS emulations are compatible with InfoPrint printers. The Universal Drivers for Windows promote efficiency in the printing environment, while maintaining the ease-of-use of our system drivers.

Support and training are simplified, as one driver can print to multiple printers, including single function and multifunction, color and monochrome, desktop and departmental. The same graphic user interface has been used to maintain continuity with our product specific drivers. Many cost-saving options, like duplex and multi-page printing, and security options like Confidential Print, as part of our Print and Hold options, are available to maximize output, minimize cost, and maintain security. The Universal Driver packages are available for various operating systems in both PCL and PostScript emulations.

Printer Drivers for UNIX and Linux systems

These printer drivers reduce the complications of printing in UNIX and Linux environments. The InfoPrint Solutions Company printer drivers provide fully scriptable command-line options. When running in X-Windows mode, The printer drivers make it easy to access many popular printer features without memorizing command line options through a GUI interface.

InfoPrint Solutions Company provides PPD files for Linux distributions using the Common Unix Printing System (CUPS). These PPD files provide the user with access to popular printing features while allowing the user to take full advantage of built-in CUPS capabilities.

InfoPrint Solutions Company Software for Macintosh

InfoPrint Solutions Company offers Max OS printing software (PPDs, PDEs, etc.) to enhance the printing experience in an Apple environment. These files allow Mac OS 9 and Mac OS X users access to advanced printing features included with this product. Printer Status complements the driver software by providing printer status feedback from a remote location. Other utilities such as Printer File Loader and Printer Settings provide means to perform targeted tasks.

Network TWAIN Scan Drivers

Network TWAIN scan drivers provide remote scanning capabilities to Windows and Macintosh computers. InfoPrint Solutions Company provides Network SANE drivers with remote scanning capabilities for Linux workstations. These drivers allow TWAIN (or SANE) compatible applications to acquire raw scan data directly from a networked InfoPrint Solutions Company multi-function printer.

USB Scan Drivers

These MFPs includes USB TWAIN data source and a Windows Imaging Architecture (WIA) scan driver. USB TWAIN for Windows offers MFP-to-host scanning capabilities to take full advantage of TWAIN compatible applications. WIA drivers for Windows XP, Window Server 2003, Windows Vista, and Windows Server 2008 provide direct scanning capabilities to applications supporting Microsoft's imaging architecture.

Microsoft Windows Certification

The InfoPrint Solutions Company laser printers include Microsoft Certified and digitally signed printer drivers and signed USB scan drivers. The driver certification indicates a high level of compatibility between the Windows operating system and the InfoPrint Solutions Company printer. Printer drivers for these products have received certification under the following operating systems:

  • Windows XP:
    • Home Edition
    • Professional Edition
    • Professional x64 Edition
  • Windows Server 2003:
    • Standard Edition
    • Enterprise Edition
    • Standard x64 Edition
    • Enterprise x64 Edition
  • Windows Vista:
    • Home Basic Edition
    • Home Premium Edition
    • Business Edition
    • Enterprise Edition
    • Ultimate Edition
    • Home Basic x64 Edition
    • Home Premium x64 Edition
    • Business x64 Edition
    • Enterprise x64 Edition
    • Ultimate x64 Edition
  • Windows Server 2008:
    • Standard Edition
    • Enterprise Edition
    • Datacenter Edition
    • Standard x64 Edition
    • Enterprise x64 Edition
    • Datacenter x64 Edition

Software

Printer drivers are provided on the Drivers and Utilities CD that is packaged with the printer. See Publications section for details.

The Windows software applications, which operate in the operating systems listed above, are best suited to run with the drivers supplied with the printer. These drivers for Windows take advantage of your printer functions and increase the printer performance wherever possible.

Operating Systems

InfoPrint 1880 MFP is compatible with applications running under the following operating systems for either local or network connections: For information about USB connections, see Local Connections.

 USB
Print NW TWAIN
Supported operating systems (printer and scan driver) Dvr TWAIN (9)
------------------------------------------------------- ----- ----- -----
Apple Macintosh (1)
Apple Mac OS 9 (9.2) Y(8) N N
Apple Mac OS X (10.2, 10.3, 10.4, or 10.5) Y Y Y
Microsoft Windows (1)
Microsoft Windows 95 4.00950 (OSR2) or later (10) Y(10) N N
Microsoft Windows 98.1st Edition (10) Y(10) N N
Microsoft Windows 98.2nd Edition (10) Y(10) N N
Microsoft Windows Me (10) Y(10) N N
Microsoft Windows NT 4 SP6 (10) Y(10) N N
Microsoft Windows NT 4 Server SP6 (10) Y(10) N N
Microsoft Windows 2000 Professional Y Y Y
Microsoft Windows 2000 Server Y Y Y
Microsoft Windows 2000 Advanced Server Y Y Y
Microsoft Windows 2000 Server running Terminal Y Y(7) Y(7)
Services
Microsoft Windows 2000 Server running Terminal Y Y(7) Y(7)
Services with Citrix MetaFrame Presentation
Server 3.0
Microsoft Windows 2000 Server running Terminal Y Y(7) Y(7)
Services with Citrix MetaFrame Presentation
Server 4.0
Microsoft Windows XP Home Y Y Y
Microsoft Windows XP Professional Y Y Y
Microsoft Windows XP Professional x64 Edition Y Y Y
Microsoft Windows Server 2003 Standard Edition Y Y Y
Microsoft Windows Server 2003 Standard Edition Y Y(7) Y(7)
Running Terminal Server
Microsoft Windows Server 2003 Standard x64 Edition Y Y(7) Y(7)
Microsoft Windows Server 2003 Standard x64 Edition Y Y Y
Running Terminal Server
Microsoft Windows Server 2003 Enterprise Edition Y Y Y
Microsoft Windows Server 2003 Enterprise Edition Y Y(7) Y(7)
Running Terminal Server
Microsoft Windows Server 2003 Enterprise x64 Y Y Y
Edition
Microsoft Windows Server 2003 Enterprise x64 Y Y(7) Y(7)
Edition Running Terminal Server
Microsoft Windows Server 2003 Standard Edition Y Y(7) Y(7)
running Terminal Services with Citrix MetaFrame
Presentation Server 3.0
Microsoft Windows Server 2003 Standard Edition Y Y(7) Y(7)
running Terminal Services with Citrix MetaFrame
Presentation Server 4.0
Microsoft Windows Server 2003 Standard Edition Y Y(7) Y(7)
running Terminal Services with Citrix MetaFrame
Presentation Server 4.5
Microsoft Windows Server 2003 Enterprise Edition Y Y(7) Y(7)
running Terminal Services with Citrix MetaFrame
Presentation Server 3.0
Microsoft Windows Server 2003 Enterprise Edition Y Y(7) Y(7)
running Terminal Services with Citrix MetaFrame
Presentation Server 4.0
Microsoft Windows Server 2003 Enterprise Edition Y Y(7) Y(7)
running Terminal Services with Citrix MetaFrame
Presentation Server 4.5
Microsoft Windows Server 2003 Standard x64 Edition Y Y(7) Y(7)
running Terminal Services with Citrix MetaFrame
Presentation Server 4.0 for Microsoft Windows
Server 2003 x64 Edition
Microsoft Windows Server 2003 Standard x64 Edition Y Y(7) Y(7)
running Terminal Services with Citrix MetaFrame
Presentation Server 4.5 for Microsoft Windows
Server 2003 Edition
Microsoft Windows Server 2003 Enterprise x64 Y Y(7) Y(7)
Edition running Terminal Services with Citrix MetaFrame
Presentation Server 4.0 x64 for Microsoft Windows
Server 2003 Edition
Microsoft Windows Server 2003 Enterprise x64 Y Y(7) Y(7)
Edition running Terminal Services with Citrix MetaFrame
Presentation Server 4.5 x64 for Microsoft Windows
Server 2003 x64 Edition
Microsoft Windows Vista Basic Edition Y Y Y
Microsoft Windows Vista Home Basic Edition Y Y Y
Microsoft Windows Vista Home Basic x64 Edition Y Y Y
Microsoft Windows Vista Home Premium Edition Y Y Y
Microsoft Windows Vista Home Premium x64 Edition Y Y Y
Microsoft Windows Vista Business Edition Y Y Y
Microsoft Windows Vista Business x64 Edition Y Y Y
Microsoft Windows Vista Enterprise Edition Y Y Y
Microsoft Windows Vista Enterprise x64 Edition Y Y Y
Microsoft Windows Vista Ultimate Edition Y Y Y
Microsoft Windows Vista Ultimate x 64 Edition Y Y Y
Microsoft Windows Server 2008 Standard Edition Y Y Y
Microsoft Windows Server 2008 Standard x64 Edition Y Y Y
Microsoft Windows Server 2008 Standard Edition Y Y(7) Y(7)
running Terminal Server
Microsoft Windows Server 2008 Standard x64 Edition Y Y(7) Y(7)
running Terminal Server
Microsoft Windows Server 2008 Enterprise Edition Y Y Y
Microsoft Windows Server 2008 Enterprise x64 Y Y Y
Edition
Microsoft Windows Server 2008 Enterprise Edition Y Y(7) Y(7)
running Terminal Server
Microsoft Windows Server 2008 Enterprise x64 Y Y(7) Y(7)
Edition running Terminal Server
Microsoft Windows Server 2008 Datacenter Edition Y Y Y
Microsoft Windows Server 2008 Datacenter x64 Y Y Y
Edition
Microsoft Windows Server 2008 Datacenter Edition Y Y(7) Y(7)
running Terminal Server
Microsoft Windows Server 2008 Datacenter x64 Y Y(7) Y(7)
Edition running Terminal Server
Novell (2)
Novell NetWare 5.1 (support Pack 6 or later) Y N N
with NDPS
Novell NetWare 6.0 (support Pack 3 or later) Y N N
with NDPS
Novell NetWare 6.5 with iPrint or NDPS Y N N
Novell NetWare 5.x, 6.x with iPrint or NDPS Y N N
Novell Open Enterprise Server for NetWare with Y N N
iPrint or NDPS
SUSE-based Open Enterprise Server (Windows Y N N
Client support only)
Print NW
Dvr SANE
-------------------------------------------------------------- ----- ----
UNIX (4)
HP-UX 11.11, 11.23, 11.31 Y N
Sun Solaris SPARC 7, 8, 9, 10 Y N
Sun Solaris x86 10 Y N
IBM AIX 5.2, 5.3, 6.1 (Colon files and enhanced printer drivers)Y N
Linux
SuSE Linux Enterprise Server 8 Y N
SuSE Linux Enterprise Server 9 Y N
SuSE Linux Enterprise Server 10 Y N
SuSE Linux Enterprise Desktop 10 Y Y
OpenSUSE 10.2 Y Y
OpenSUSE 10.3 Y Y
OpenSUSE 11.0 Y Y
Red Hat Enterprise Linux WS 3 Y Y
Red Hat Enterprise Linux WS 4 Y Y
Red Hat Enterprise Linux WS 5 Y Y
Debian GNU/Linux 4.0 Y Y
Linspire 6.0 Y Y
Red Flag Linux Desktop 5.0 (Simplified Chinese only) Y Y
Red Flag Linux Desktop 6.0 (Simplified Chinese only) Y Y
Linpus Linux Desktop 9.2 (Traditional Chinese only) Y Y
Linpus Linux Desktop 9.3 (Traditional Chinese only) Y Y
Ubuntu 7.10 Y Y
Ubuntu 8.04 LTS Y Y
Other
Virtually any platform supporting TCP/IP (5) Y N
IBM iSeries and AS/400 Systems with TCP/IP with OS/400(r) Y N
V3R1 or later using OS/400 Host Print Transform (5).
SAP Device Type support Y N


Note: (1) Download the latest printer drivers from InfoPrint Web Site

Note: (5) Drivers for these operating systems are not provided by InfoPrint.

Note: (7) TWAIN support in Terminal Server environments requires a Terminal Server-aware TWAIN application see:

https://support.microsoft.com/kb/186499 for more information

Note: (8) Network print via TCP/IP is supported. If local printing support from Mac OS9 is required, a special version of code must be obtained from the Techical Support Center. This special code however, will disable local scanning.

Note: (9) WIA scan driver also provided where appropiate (no WIA for Windows 2000)

Note: (10) Printing support only by using Universl Driver, available at:

infoprint.com.

No scan support is available.

Infoprint Manager

Infoprint Manager support: Yes (post GA). Requires administrators to create printer objects.

Physical Specifications

Dimensions

 Width Depth Height Weight
--------------- --------------- --------------- ------------
fd1 548.0 mm 596.0 mm 1114.0 mm 75.1 kg
model (21.6 in) (23.5 in) (43.9 in) (165.5 lb)

bd1 548.0 mm 596.0 mm 1114.0 mm 72.8 kg
model (21.6 in) (23.5 in) (43.9 in) (160.6 lb)

tf1 548.0 mm 596.0 mm 1246.0 mm 80.1 kg
model (21.6 in) (23.5 in) (49.1 in) (176.5 lb)

tb1 548.0 mm 596.0 mm 1246.0 mm 77.8 kg
model (21.6 in) (23.5 in) (49.1 in) (171.6 lb)

550-Sheet 548.0 mm 548.0 mm 132.0 mm 5.0 kg
Drawer (21.6 in) (21.6 in) (5.2 in) (11.0 lb)

Caster Base 768.0 mm 801.0 mm 107.0 mm 38.5 kg
(30.3 in) (31.6 in) (4.2 in) (85.0 lb)

Envelope (1) 233.0 mm (1) 2.0 kg
Feeder (9.2 in) (4.4 lb)
(closed position)

Envelope (1) 350.0 mm (1) 2.0 kg
Feeder (13.8 in) (4.4 lb)
(support fully
extended)

Note: (1) Envelope feeder fits within height and width of printer.

Minimum clearance requirements

 Left side Right side Front Rear Top
------------ ------------ ----------- ------------ ------------
304.8 mm 203.2 mm 508.0 mm 203.2 mm 304.8 mm
(12 in) (8.0 in) (20 in) (8.0 in) (12 in)

Note: When installing the printer, the customer should allow enough room to access the paper trays and paper exits.

Operating Environment

Operating environment
Air Temperature - product operating 15.6 to 32.2 C (60 to 90 F)
Air Temperature - product powered off 10.0 to 43.3 C (50 to 110 F)
Air Relative Humidity 8% to 80% relative humidity
Wet Bulb Temperature - product operating 22.8 C (73.0 F) Maximum
Wet Bulb Temperature - product powered off 26.7 C (80.1 F) Maximum
Altitude 0 to 3,048 meters (10,000 ft)
Atmospheric Pressure Less than 74.6 kPa
Ambient Operating Environment (a) 15.6 to 32.2 C (60 to 90 F)
and 8% to 80% RH

Storage and shipping environment (packed)
Cartridges (packaged) -40 to 43.3 C (-40 to 110 F)
Printer with Cartridges (packaged) -40 to 43.3 C (-40 to 110 F)
Air Relative Humidity (unpackaged) Relative Humidity 8% to 80%
Air Relative Humidity (packaged) Relative Humidity 5% to 95%
Altitude Less than 10,300 meters
(34,000 feet)


Note: (a) In some cases performance specifications (such as paper feed error or PFE, EP cartridge usage) are specified to be measured at an ambient condition.

Electrical specifications

Low voltage models

  • 100 - 127 V ac at 50 - 60 Hz, nominal
  • 90 - 137 V ac, extreme

Average power consumption

The following table specifies nominal average power requirements for the base printer configuration for InfoPrint 1880 MFP.

Printing states
--------------------------------- --------------
Off 0 W
Ready Mode 105 W
Continuous Printing (simplex) 800 W
Continuous Printing (duplex) 650 W
Continuous Copying 875 W
Continuous Scanning 165 W
Typical electricity consumption test 9.72 KWH/wk

Average current while printing
120 Volts 8.5 a
230 Volts 4.5 a


Notes

  • Using a 220 V ac to 110 V ac power converter with the low voltage model is not recommended.
  • All models are ENERGY STAR compliant.
  • All models ship with Power Save Mode = On

Acoustics

All measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.

 1 Meter Average Declared Sound
Mode Sound Pressure (dBA) Power Level (Bels)
----------------------- -------------------- ------------------
Idle (Standby mode) 28 4.5
Simplex printing 55 7.1
Duplex printing 55 7.1
ADF Mono Scan 55 7.2
ADF Mono Copy 55 7.2
ADF Color Scan 50 7.1
Mono "Quiet Mode" Printing 50 6.6


Limitations

Not applicable.

Hardware Requirements

Not applicable.

Software Requirements

Not applicable.


Publications

All hardcopy publications are downloadable from the InfoPrint Solutions Company Web site:

https://www.infoprint.com

The following publications are shipped with the products:

  • Software and Documentation CD

User's Guide (contained on CD)

This will be available in the following languages: Arabic, English, Danish, Dutch, Finnish, French, German, Hebrew, Italian, Korean, Norwegian, Polish, Brazilian Portuguese, Romanian, Russian, Spanish, Swedish, Simplified Chinese, Traditional Chinese, and Turkish.

Operator Panel

This will be available in the following languages: English, Danish, Dutch, Finnish, French, German, Italian, Norwegian, Polish, Brazilian Portuguese, Russian, Spanish, Swedish, Turkish, Simplified Chinese, Traditional Chinese, Korean, and Japanese.

Special Feature Codes -- Chargeable
Mach Feature Part
type Model number number Description UPC
---- ----- ------- ------- ------------------------------ ---------------
4568 fd1 39V3069 InfoPrint 1880 MFP 8-83436-03713-6
4568 tf1 39V3070 InfoPrint 1880 MFP 8-83436-03714-3
4568 bd1 39V3073 InfoPrint 1880 MFP 8-83436-03717-4
4568 tb1 39V3074 InfoPrint 1880 MFP 8-83436-03718-1
39V2963 550-Sheet Drawer 8-83436-04174-4
ServicePacs

Machine Electronic
Type Model Description Part Number
------- ----- ------------------------------- -----------
4568 All SVCPAC PTR 2YR IOR 9X5/NBD 54Y5046
4568 All SVCPAC PTR 3YR IOR 9X5/NBD 54Y5047
4568 All SVCPAC PTR 1YR IOR 24X7/SD 54Y5050
4568 All SVCPAC PTR 2YR IOR 24X7/SD 54Y5051
4568 All SVCPAC PTR 3YR IOR 24X7/SD 54Y5052
4568 All SVCPAC PTR 1YR IOR 9X5/NBD (MA) 54Y5055
4568 All SVCPAC PTR 2YR IOR 9X5/NBD (MA) 54Y5056
4568 All SVCPAC PTR 1YR IOR 24X7/SD (MA) 54Y5057
4568 All SVCPAC PTR 2YR IOR 24X7/SD (MA) 54Y5058


Printer Features

All printer features are customer installable.

Input, Output and Other Media Features

The range of media weights, types and sizes supported by each of these options is described under Media Support. The maximum configuration of paper options supported by each printer model is also described within Media Support.

The InfoPrint 1880 MFP media features include:

(P/N 39V2963) 550-Sheet Drawer

  • Minimum required = 0, maximum allowed = 4
  • Prerequisite =none, Co-requisite = none

This optional input source installs beneath the printer, and it holds approximately 550 sheets of (20 lb.) paper. Multiple optional drawers are supported simultaneously.

(P/N 39V2965) Envelope Feeder

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite =none, Co-requisite = none

Although occasional envelope printing is supported through the printer's multi-purpose tray, this option is available for more frequent envelope printing. It holds up to 85 envelopes (20lb or 75 gsm).

Memory and Flash Memory Features

The InfoPrint 1880 MFP has one slot for additional memory DIMMs and one slot for flash memory cards.

The memory features include the following SDRAM features:

The following font cards plug into the flash memory slot. Only one flash memory card or one font card is supported.

The optional DBCS (Double-Byte Character Set) Font Cards provide printer resident fonts for use printing Simplified Chinese, Traditional Chinese, Japanese and Korean. The Chinese and Japanese font cards also contain a display font used for displaying Chinese and Japanese on some MFP devices. The DBCS Font Cards are suitable for use in a range of InfoPrint Solutions Company printers and MFPs. Fonts contained in these cards emulate those provided in Microsoft Windows. The use of printer-resident fonts in the card improves performance and minimizes network traffic since less data is downloaded to the printer. Each font card supports encodings appropriate for the language, including Adobe CID encodings.

(P/N 39V3619) Simplified Chinese Font Card

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none

(P/N 39V3620) Traditional Chinese Font Card

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none

These two cards are for use with PCL and PostScript emulation. DBCS font support is available for the following languages:

  • Simplified Chinese for China with two scalable print fonts and one display font.
  • Traditional Chinese for Taiwan with two scalable print fonts and one display font.

The fonts used with the PCL emulation are compatible with the fonts in the HP LaserJet Language DIMM Memory options for Traditional Chinese and Simplified Chinese, which are compatible with the HP LaserJet 4050, 4000, 4000 N, 4000 T and 4000 JN. These fonts are available in the PostScript emulation and are compatible with Adobe PostScript 3.

(P/N 39V3621) Japanese Font Card

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none

The Japanese Font Card contains two scalable print fonts for use with PCL and PostScript emulation and one display font. The Postscript fonts are compatible with Adobe PostScript 3 and emulate Adobe PostScript fonts such as those in the Ricoh NX750. The fonts used with the PCL emulation are compatible with the fonts in the HP LaserJet Language DIMM Memory options for Japanese, which are compatible with the HP LaserJet 4050, 4000, 4000 N, 4000 T and 4000 JN.

(P/N 39V3618) Korean Font Card

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none

The Korean Font Card contains eight scalable print fonts for use with PCL and PostScript emulation and is compatible with Adobe PostScript 3. The fonts used with the PCL emulation are compatible with the fonts in the HP LaserJet Language DIMM Memory options for Korean, which are compatible with the HP LaserJet 4050, 4000, 4000 N, 4000 T and 4000 JN.

(P/N 39V3415) 256 MB Memory DIMM

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none

(P/N 39V3416) 512 MB Memory DIMM

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none

(P/N 39V3417) 1024 MB Memory DIMM

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none

The flash memory features include:

(P/N 39V3593) 256 MB Flash Card

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none

The hard disk feature includes:

Application Solution features

These features plug into the one application solution slot.

(P/N 39V3464) Bar Code Card

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none
  • Conflict = IPDS & SCS/Tne Card and Decryption Card

Bar Code capabilities included on the card provide the ability to algorithmically generate more than forty seven of the most popular industry standard bar codes, including Datamatrix, QR Code, and Codablock F. The bar code function emulates HP printers with an HP BarCodes & More font solution, JetCAPS BarDIMM or JetCAPS BarSIMM (v. 2.0b).

(P/N 39V3463) Decryption Card

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none
  • Conflict = IPDS & SCS/Tne Card and Bar Code Card

The Decryption Card supports AES encryption using key and block lengths of 128, 192, and 256 bits, providing robust security for sensitive documents. It also supports the use of Session or dynamic encryption keys, which greatly reduces management overhead. Session keys are automatically and randomly generated with each print job, ensuring that a unique key is applied to each print job.

(P/N 39V2693) IPDS & SCS/Tne Card

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none
  • Conflict = Bar Code Card and Decryption Card

This feature provides configuration flexibility and compatibility for AFP/IPDS or SCS printing on TCP/IP LAN printers. It is compatible with IBM mainframe or IBM iSeries and AS/400 applications that generate SCS (LU1) output or with applications that output AFP/IPDS through the Print Services Facility (PSF).

This feature provides IS or IT managers an affordable printing solution in a distributed network or on a local area network for applications or software that generate AFP/IPDS or SCS. The IPDS and SCS/TNe Card offers customers the following benefits:

  • Print PostScript, PCL, AFP/IPDS, SCS, and other local area network printer documents from mainframe, iSeries, or AS/400 systems on one printer.
  • Supports IPDS FS45 for full color printing. On monochrome printers, color documents can be transformed to black or shades of gray, based upon the IPDS menu Color Mode setting.
  • Support for the following object types: Encapsulated PS, Encapsulated PS with Transparency, TIFF and GIF.
  • IPDS N-up and N-up Explicit Page Placement support. Print 1 to 4 partitions per side or 8 partitions per sheet when printing duplex pages.
  • IPDS PDF417, DataMatrix, Maxicode and Quick Response (QR) 2D bar code support in the bar code tower.
  • United States Postal Service 4 state bar code support (Intelligent Mail Barcode).
  • Download DBCS outline and bitmap fonts from the host in IPDS. Support for Simplified Chinese, Traditional Chinese, Korean, and Japanese is provided.
  • Supports downloaded True Type fonts
  • Capture bitmap or outline fonts to an optional flash memory or optional hard disk using AFP/IPDS and PSF. This results in reduced network traffic over local area networks.
  • Supports TN3270E or TN5250E SCS (LU1) over the LAN using TCP/IP with Telnet.
  • Emulates common IBM IPDS and SCS printers.
  • Automatic resolution sensing for IPDS when the Host Resolution menu item is set to Auto. Selecting Auto allows 240, 300 and 600 dpi resources to be downloaded from the host.
  • Product Identifier Self Defining Field Information is returned to the host with IPDS. Device type, serial number, printer code levels and printer name are returned to the host. These may be displayed at the host to aid in printer location and maintenance.
  • Print PostScript, PCL, AFP/IPDS, SCS, and other local area network printer documents from mainframe, iSeries, or AS/400 systems on one printer.
  • Configure SCS/TNe and IPDS settings using a printer resident web server, a browser, and the printer's IP address.

The IPDS and SCS/TNe Card is an option that is installed in the printer application solution slot. With this card and the standard Ethernet TCP/IP port, the printer becomes an IBM host workstation printer capable of printing AFP/IPDS or SCS documents from an IBM iSeries, AS/400, or mainframe computer.

The printer emulates an IBM mainframe, iSeries, or AS/400 host printer when used with the appropriate host software and this card. The printer emulates one TN3270E printer session and up to four TN5250E printer sessions using the LU1 SCS data stream over TCP/IP with the TN3270E and TN5250E extended Telnet protocol support in this option. This is supported directly from an iSeries, AS/400, or from a mainframe using TCP/IP or through any TN3270E capable gateway that supports TN3270E according to RFC 2355. The DSC/DSE or SCS data streams over LU3 or LU0 are not supported. The Telnet protocol function is only supported with the printer through the standard Ethernet network port or with the internal print servers.

The printer can be configured to save IPDS resources when attached to a LAN through the standard Ethernet port. This will improve performance on complex IPDS print jobs with host resources such as fonts, overlays, or page segments.

The IPDS emulation supports the IPDS data and resource towers. Fonts can be downloaded, captured and saved to an optional flash memory or optional hard disk in the printer. The US Postal Service (USPS) POSTNET bar code, USPS PLANET bar code, USPS 4 slate bar code, and the euro currency symbol are supported within IPDS. The euro currency symbol is also supported in the SCS, PostScript and PCL 6 emulations.

DBCS characters in Traditional Chinese, Simplified Chinese, Korean, and Japanese can be downloaded and printed from the host. DBCS fonts may be stored in flash memory or on the hard disk using the Font Capture feature to reduce network traffic and transmission time. The separate DBCS Font Cards cannot be used with the IPDS and SCS/TNe Card.

Cable Features

(P/N 75P7029) 10 Ft. Parallel Cable

  • Minimum required = 0, maximum allowed = no maximum
  • Prerequisite = none, Co-requisite = none

This IEEE 1284 cable allows the user to connect one laser printer to one host machine (or external print server). The cable is 10 feet in length and provides a DB-25 pin connector for the host and a 36-pin Centronics connector for the printer.

(P/N 75P7030) 2-meter USB Cable

  • Minimum required = 0, maximum allowed = no maximum
  • Prerequisite = none, Co-requisite = none

This 2 meter USB cable allows the user to connect one laser printer to one host machine (or external print server). The cable provides a USB "A" connector for the host machine and a USB "B" connector for the printer.

Internal Connection Features

There is one slot for the following internal connection features.

(P/N 39V3608) Ethernet 1000BaseTX

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none

(P/N 39V3623) 802.11b/g/n Wireless Print Server

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none

This feature support Gigabit Ethernet.

(P/N 39V3423) Parallel 1284-B Interface Card

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none

(P/N 39V3424) RS-232C Serial Interface Card

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none

External Print Servers Features

Theses external features plug into a USB port on the printer.

(P/N 39V1524) Ethernet 10BaseT/100BaseTX (1 USB port)

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none

(P/N 39V1525) Ethernet 1000BaseTX (4 USB ports)

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none

(P/N varies by country) 802.11g Wireless to USB

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = network model or Ethernet feature, Co-requisite =none

This external feature allows the printer to be connected directly to a wireless LAN using the IEEE 802.11g wireless standard. This standard operates at speeds of up to 54 megabits per second (Mbps). The range of this wireless adapter depends on the environment, whether used indoors or outdoors and building construction. Typical indoor ranges are 20-50 meters and outdoor ranges are 100-200 meters. Performance will degrade with distance. The wireless LAN feature is compliant with any WiFi-compliant device.

The feature is an external adapter that connects to the standard USB port on the printer.

Furniture Features

The following furniture features are available.

(P/N 39V3615) 5 in. Spacer

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none

(P/N 39V3588) Caster Base

  • Minimum required = 0, maximum allowed = 1
  • Prerequisite = none, Co-requisite = none

Trademarks

(R), (TM), * Trademark or registered trademark of International Business Machines Corporation.

** Company, product, or service name may be a trademark or service mark of others.

InfoPrint is a trademark of InfoPrint Solutions Company LLC in the United States, other countries, or both.

Windows is a trademark of Microsoft Corporation.

UNIX is a registered trademark in the United States and other countries licensed exclusively through X/Open Company Limited.
- IBM Corporation 2008.